A foreman for an injection-molding firm admits that on 46% of his shifts, he forgets to shut off the injection machine on his line. This causes the machine tooverheat, increasing the probability that a defective molding will be produced during the early morning run from 2% to 18%...
choose proper punctuationGeorge, leave the room, shut the door, and be quietb)George;leave the room, shut the door and be quietc)George leave the room, shut the door and be quietd)b)George leave the room, shut the door, and be quietMy first guess is a)but I'm tempted to chose b)
A car owner forgets to turn off the headlights of his car while it is parked in his garage. If the 12.0-V battery in his car is rated at 142.0 A · h and each headlightrequires 31.2 W of power, how long will it take the battery to completely discharge? h
Luigi rides his bike to school, and forgets his lunch. 10 min after he leaves the house, his mother starts to drive after him in her car. The speed of her car is 22mph. Luigi rides his bike at 12 mph. How long until the mother catches up?
{COMPLETE QESTION}Marotta Company produces plastic that is used for injection-molding applicationssuch as gears for small motors. In 2010, the first year of operations, Marottaproduced 4,000 tons of plastic and sold 3,000 tons. In 2011, the production andsales results were exactl...
Jackson Company produces plastic that is used for injection-molding applications such as gears for small motors. In 2016, the first year of operations, Jackson produced 4,900 tons of plastic and sold 3,920 tons. In 2017, the production and sales results were e...
An injection molding machine can be purchased and installed for $90,000. It is in the seven-year GDS property class and is expected to be kept in service for eight years. It is believed that $10,000 can be obtained when the machine is disposed of at the end of year eight. The net...
1. Design a clay-filled PE composite suitable for injection molding inexpensive parts. The final part must have a tensile strength > 3000 psi and a modulus> 80,000 psi PE costs $0.50/lb and clay costs $0.05/lb density PE 0.95 g/cm3, density clay 2.4 g/cm3 The plot below ma...
What are the main processing parameters that influence the viscosity of a polymer in an extrusion process explain this for 3D FDM printing as well as injection molding
What are the main processing parameters that influence the viscosity of a polymer in an extrusion process explain this for 3D FDM printing as well as injection molding
1. Many so-called Founding Fathers are famous one or two of (his, his or her, their) accomplishments, but anyone who knows (his, his or her, their) history knows that Franklin is known for many things, including (his, her, his or her, their) inventions.their, his or her, their2....
y-SE (10 marks) Question2 A 3-liter, four-cylinder engine is equipped with multipoint port fuel injection, having Cone injector per cylinder. Maximum power is obtained at WOT when injection duration is continuous. At this condition, engine speed is 6000 RPM with stoichiometr...
14) An order is written for 10 mL of a 10% calcium chloride injection and 10 mL of multivitamin injection (MVI) to be added to1000 mL of DSW. The infusion is to be administered over 6 hours. The IV set delivers 10 drops/ mL. What should be the rate of flow in drops per minut...
Maureen forgets to turn a faucet off. After a minute, 1.5 gallons of water comes out of the faucet. Which equation can bw used to find the number of gallons, g, that comes out of the faucet after 2 hours?A. g= 1.5 x 1/30B. g=1.5 x 1/120C. g=1.5 x 120D. g= 1.5 x 604
Problem 1: a. Draw a situation where a perfectly competitive firm is making a loss, make sure to label loss. When should the firm shut down? (Make sure to include a market diagram). b. State and draw a graph explaining the long run equilibrium in a perfectly competitive market. W...