Homework Help Question & Answers

Q1. Load and Stress Analysis The countershaft with the reverse gears attached to is shown in figu...

Q1. Load and Stress Analysis The countershaft with the reverse gears attached to is shown in figure 2 with the dimension give

LI し2 し3 CB dia. d Driven gear A dia. du Pinion gear iB dia. dB Figure 2. Gear A and B attached to the countershaft.

4 Value Vlne 2 8 12 Unit 2 |!。。。..(L + L.) | 225 1500 × (l+ 은)| 666.4 L9 | mm

machine design question

Q1. Load and Stress Analysis The countershaft with the reverse gears attached to is shown in figure 2 with the dimension given in table 1. Gear A receives power from another gear with the transmitted force Fa applied at the pressure angle au as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fs at the pressure angle shown. You can find the values of the parameters in table 1 [10 points] a) Determine the force Fe, assuming the shaft is running at a constant speed. simple supports. set for the horizontal plane and another set for the vertical plane. b) Find the magnitudes of the bearing reaction forces, assuming the bearings act as c) Draw shear-force and bending-moment diagrams for the shaft. If needed, make one d) At the point of maximum bending moment, determine the bending stress and the torsional shear stress. e) At the point of maximum bending moment, determine the principal stresses and the maximum shear stress.
LI し2 し3 CB dia. d Driven gear A dia. du Pinion gear iB dia. dB Figure 2. Gear A and B attached to the countershaft.
4 Value Vlne 2 8 12 Unit 2 |!。。。..(L' + L.) | 225 1500 × (l+ 은)| 666.4 L9 | mm
0 0
Next > < Previous
ReportAnswer #1

Bending moment, shear force and bending stress all data are submitted in files below:LI し2 し3 CB dia. d Driven gear A Radial comp Tangential component dia. da Tangential component r gar B dia. dB Radial auSolution Part(A) :-FB=2 As per the given table > 0 Nou we havet calculate the tangentia and radial Component :- Tan ential couwhere is the angular speed n radian/sec here - in rpm 6 0 w = 837.76 Yad/s So from equation (2)、 power Ps 88.39 x 837.76 Ps<ince we knolo thot he shaft runs at constan speed means usa=we ço TA-TG because Hence Ta=TB二88.29 N-m Also we know that TaugPart (BI :- Bearina reactions Cxy) plane (FB)z 296 S N LI = 600 mm 17S mm Ro F58.5+N Equilibrium RotRe --992. 09 N Taleiu omeand Roz 1081.84-1557 . ys Answer of part e Part (C):- Bendiuy mowant aud shear force diagram: X 296.S 32.9 о. 175 S9.17 Sheaς.F.D and B.M. D for Xz plane:- 139u.79 N 312 9SN SS7.45N 139u-79 N S.F.D 162 66 N u7S. GN В.М.D A. 285.3 313.83 N- m From boHence max bendij omeut (Bot planz ) Now maximum bendiua stress maX ovevall maximum bendiuastress Part (e):3 al-Pointe 49.16 M

Comment
Comments
    Know the answer?
    Add Answer of:
    Q1. Load and Stress Analysis The countershaft with the reverse gears attached to is shown in figu...
    Your Answer: Your Name: What's your source?
    Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
    Similar Homework Help Questions
    • Solid Mechanics Design Question

      A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power istransmitted through the shaft anddelivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent ofthe tension on the tight side.(a) Determine the tensions in the belt on pulley B, assuming the shaft is running at a constantspeed.(b) Find the magnitudes of the...

    • A countershaft carrying two V-belt pulleys is shown in figure 1 (dimensions in inches). Pulley A...

      A countershaft carrying two V-belt pulleys is shown in figure 1 (dimensions in inches). Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side. a) At the point of maximum bending moment, determine the principal stresses and the maximum shear...

    • Shaft, free body diagram, reaction forces, bending moment, stresses... Please help and you will...

      A countershaftcarrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmittedthrough the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side.a) Determine the tensions in the belt on pulley B, assuming the shaft is running at a constant speed.b) Find the magnitudes...

    • I. The countershaft shown in the Fig Q1 has two spur gears mounted on it with teeth cut wi a 20 pressure angle....

      I. The countershaft shown in the Fig Q1 has two spur gears mounted on it with teeth cut wi a 20 pressure angle. The shaft (grooved) is to be made of cold-drawn AISI 1040 steel havin Sut 779 MPa and S,-593 MPa, an elongation of 19% and HB-262. You are asked to size the shaft for safe operation according to DE-Elliptic criterion by using a factor of safety of 2.5 and a reliability of 99 percent. The stress-concentration factors for...

    • 1. The countershaft shown in the Fig QI has two spur gears mounted on it with teeth cut with a 20 pressure angle...

      1. The countershaft shown in the Fig QI has two spur gears mounted on it with teeth cut with a 20 pressure angle. The shaft (grooved) is to be made of cold-drawn AISI 1040 steel having Sut= 779 MPa and S,-593 MPa, an elongation of 19% and HB-262. You are asked to size the shaft for safe operation according to DE-Eilliptic criterion by using a factor of safety of 2.5 and a reliability of 99 percent. The stress-concentration factors for...

    • Engineering Design-1

      A countershaft carrying two V-belt pulleys is shown in figure 1 (dimensions in inches). Pulley A receives power from a motor through a belt with the belt tensionsshown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is15 percent of the tension on the tight side.a) At the point of maximum bending moment, determine the principal stresses and the maximum shear stress.b) Determine the...

    • A countershaft, made of AISI 1035 CD steel, carrying two V-belt pulleys is shown in the figure. P...

      A countershaft, made of AISI 1035 CD steel, carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 25 percent of the tension on the tight side (F2 - 0.25 F) 1) Based on the equations for yielding conditions discussed...

    • 2. Given the shaft specifications and gear diameters, determine largest allowable force P2. gear A diameter-300 mm gear C diamter 400 mm alow60 MPa dshaft44 mm 80 mm 25O mm 250 1. Set P1 1 kN 2....

      2. Given the shaft specifications and gear diameters, determine largest allowable force P2. gear A diameter-300 mm gear C diamter 400 mm alow60 MPa dshaft44 mm 80 mm 25O mm 250 1. Set P1 1 kN 2. Find torque between A and C 3. Calculate shear stress 4. Find maximum moment about y-axis (fbd of x-z plane) 5. Find maximum moment about z-axis (fbd of y-z plane) 6. Find resultant moment 7. Calculate normal stress for resultant bending moment 8....

    • Please help. Thx Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a...

      Please help. Thx Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a pitch diameter of 2 inches, and has 20 teeth. The gear "Ghas 120 teeth. All teeth have a pressure angle of 20, full-depth, hobbed profile, and a face width of 0.5 inches. All materials are steel. Determine: A) Minimum number of pinion teeth: Np,min This shows that...

    • Determine the torque on the shat in section BC

      1. In the figure shown above the tension, T2, on the slack side is 0.15 T1. The reaction forces at O and C are determined as: O=-222.7j-123k, andC=-127.3j-328ka) Determine the value of tension T1 in the pulley at location B.b) Determine the torque on the shat in section BCc) Determine the torque on the shaft in section ABd) Determine the bending moment on the shaft to the left of point B.e) Determine the shear force to the right of point...

    Need Online Homework Help?
    Ask a Question
    Get Answers For Free
    Most questions answered within 3 hours.
    Share Your Knowledge

    Post an Article
    Post an Answer
    Post a Question with Answer

    Self-promotion: Authors have the chance of a link back to their own personal blogs or social media profile pages.