you have two different transistor a PNP and the other NPN ,one power supply ,one led (1.5 V),many resistors . Design a touch switch circuit and label the values of the Vcc and resistors on your design...

you have two different transistor a PNP and the other NPN ,one power supply ,one led (1.5 V),many resistors .
Design a touch switch circuit and label the values of the Vcc and resistors on your design and explain how it work briefly.
note :you must use the two transistors you can not use only one

Circuit diagram:

Add Answer of: you have two different transistor a PNP and the other NPN ,one power supply ,one led (1.5 V),many resistors . Design a touch switch circuit and label the values of the Vcc and resistors on your design...
Similar Homework Help Questions
• Design a pnp transistor circuit using one emitter and one collector resistor connected appropriat...

Design a pnp transistor circuit using one emitter and one collector resistor connected appropriately to ±3 V voltage sources so that IE-0.5 miA and VBC-1V. Use β = 100. Design a pnp transistor circuit using one emitter and one collector resistor connected appropriately to ±3 V voltage sources so that IE-0.5 miA and VBC-1V. Use β = 100.

• A. Design one circuit: Including power supply values and connections. 1-Design a non-inverting am...

A. Design one circuit: Including power supply values and connections. 1-Design a non-inverting amplifier with a gain of +11 V/V (+/- 10%) with an input of 0.5 V sin(2pi 200t). 2-Design an inverting amplifier with a gain of -22 V/V (+/- 10%) with an input of 0.12 V sin(2pi500t) 3-Design a 555 time astable with a 1 Hz output to an LED load 4-Design a single stage low-pass filter with a cutoff frequency of 300 Hz.

• Need help with schematics for blocks 3, 4 and 5!!!!!! Include all schematics and wiring along with the component values...

Need help with schematics for blocks 3, 4 and 5!!!!!! Include all schematics and wiring along with the component values and how you acquired them. Explain how each block functions and label any figures. Need schematics for blocks 3, 4 and 5!!!!!! Goal For your final project you will be asked to design and assemble a system in which you will input a stereo audio signal, mix the channels into a single mono signal, amplify the signal, filter it to...

• FIND THE VALUES OF Rb1, Rb2, Re,Rc, rin , rout, overall gain and open circuit gain First, design a common emitter BJT a...

FIND THE VALUES OF Rb1, Rb2, Re,Rc, rin , rout, overall gain and open circuit gain First, design a common emitter BJT amplifier Second, analyze the amplifier.( Avo, Gv, Rin, Rout) Third, compare your calculation with Multisim. Report must include comparison between your calculation & simulation results overall voltage gain, open circuit voltage gain, input resistance, and output resistance. This design project is not group work, must be done individually. Type your report. Design a discrete common emitter BJT amplifier.(Determine...

• For the circuit shown below, design the values of R1 and R2 that will cause Vout-6 Vif VIv-9 V. If the resistors you chose have a tolerance of 1 %, what is the maximum and minimum values of Vout? Des...

For the circuit shown below, design the values of R1 and R2 that will cause Vout-6 Vif VIv-9 V. If the resistors you chose have a tolerance of 1 %, what is the maximum and minimum values of Vout? Design R3 so that the LED will be properly lit, if IF=10 mA, VF-3 V and Vout-6 V Design equations from the data sheet: VOUT-1.25%(1+R2 R1) U1 OUT ININLT OUT R3 R1 V1 (R3) R1) ADJ LT317A D1 IN) R2 (R2)...

• In this part of the term paper, design a single-phase switch-mode DC power supply with a forward ...

In this part of the term paper, design a single-phase switch-mode DC power supply with a forward converter. Provide answers to the questions below Please combine the single-phase full-wave rectifier from part two of your term paper with a forward converter to produce a switch-mode DC power supply, as shown below. The output of the bridge rectifier serves as input to the forward converter L1 Np: N BH621BH62 D, V1 Load C1 100p 45 Vrms D3 BH62 18H62 D4 Control...

• Laboratory 2: Transistor circuit characteristics A. Objectives: 1. To study the basic characteris...

Laboratory 2: Transistor circuit characteristics A. Objectives: 1. To study the basic characteristics of a transistor circuit. 2. To study the bias circuit of a transistor circuit. B. Apparatus: 1. DC Power supply 2. Experimental boards and corresponding components 3. Electronic calculator (prepared by students) 4. Digital camera (prepared by students for photo taking of the experimental results) 5. Laptop computer with the software PicoScope 6 and Microsoft Word installed. 6. PicoScope PC Oscilloscope and its accessories. 7. Digital multi-meter....

• Consider the circuit beloW consisting of a single power source and five resistors. 5 The values...

Consider the circuit beloW consisting of a single power source and five resistors. 5 The values in the circuit are as follows: RI-17.5 Ω R2 27.6 Q R3-96.5 Ω R4-144.6 Ω R5 63.4 Calculate the current (l0) supplied by the power source. Use units of "A" or Starting with your result for lo from the previous question, calculate the voltage drop across R5 (use units of "V" or "Volts"). Calculate the power dissipated in resistor R4 (use units of "W"...

• Using a circuit analysis technique of your choosing, calculate the power balance of the system at...

Using a circuit analysis technique of your choosing, calculate the power balance of the system at midday. Show all working. Comment on the effectiveness (calculate percentages) of power transfer from the solar panel to the LED lights, and how much is dissipated in the wiring. If LED brightness is proportional to current, express the relative brightness of the LED lights if LED 3 is used as a reference (100%), a=560 b=0.92 c=28 d=2.8 e=2.4 f=6.6 g=31.5 Sarah the sommelier wants...

• (C) Using a circuit analysis technique of your choosing, calculate the power balance of the system at midday. Show all working. Comment on the effectiveness (calculate percentages) of power transfer f...

(C) Using a circuit analysis technique of your choosing, calculate the power balance of the system at midday. Show all working. Comment on the effectiveness (calculate percentages) of power transfer from the solar panel to the LED lights, and how much is dissipated in the wiring. If LED brightness is proportional to current, express the relative brightness of the LED lights if LED 3 is used as a reference (100%), a=560 b=0.92 c=28 d=2.8 e=2.4 f=6.6 g=31.5 (d) Use circuit...

Need Online Homework Help?