Draw a per unit impedance diagram for the system whose one-line diagram shown in Fig.1. The three phases and line-to-line ratings are as given in the figure. Assume the load is a parallel combination of Resistance and reactance (R&X). Select a base of 100

Question

Question

But-The-Base-Voltage

Answer 1

Similar Homework Help Questions

Obtain the per unit impedance and reactance diagram of the power system shown in Figure.1 G1...

Obtain the per unit impedance and reactance diagram of the power system shown in Figure.1 G1 : 30MVA, 10.5KV, X” = 1.6 Ω G2 : 15MVA, 6.6KV, X” = 1.2 Ω G3 : 25MVA, 6.6KV, X” = 0.56 Ω T1 (Three Phase) : 15MVA, 33/11 KV, X=15.2 Ω per phase on high tension side. T2 (Three Phase) : 15MVA, 33/6.2 KV, X=16 Ω per phase on high tension side. Transmission line = 20.5 Ω / phase Load A = 15...
Consider the system Shown in the single-line diagram of Figure (3). All reactance are shown in per unit to the same base
Consider the system Shown in the single-line diagram of Figure (3). All reactance are shown in per unit to the same base.

G 3. Draw the reactance diagram for the power system shown in Figure.3. The ratings of...

G 3. Draw the reactance diagram for the power system shown in Figure.3. The ratings of generator, motor and transformers are given below. Neglect resistance and use a base of 50 MVA, 138 kV in the 40 Ohms Line :20MVA, 18 kV, X = 20% :20MVA, 18 kV, X = 20% Synchronous Motor: 30MVA 13.8Kv X = 20% 3-phase, Star-Star Transformer: 20 MVA, 138/20 kV, X= 10% 3-phase, Star-Delta Transformer: 20 MVA, 138/20 kV, X = 10% G2 y j4012...
Consider the system Shown in the single-line diagram of Figure (3). All reactance are shown in per unit to the same base. Assume that the voltage at both sources is 1 p.u.

Consider the system shown in the single-line diagram of Figure (3). All reactances are shown in per unit to the same base. Assume that the voltage at both sources is \(1 \mathrm{p}\).u. a- Find the fault current due to a bolted- three-phase short circuit at bus \(3 .[10\) points \(]\) b- Find the fault current supplied by each generator and the voltage at each of the buses 1 and 2 under fault conditions. \([10\) points \(]\)
Consider the system Shown in the single-line diagram of Figure (3). All reactance are shown in per unit to the same base. Assume that the voltage at both sources is 1 p.u.

Consider the system Shown in the single-line diagram of Figure (2). All reactance are shown in per unit to the same base. Assume that the voltage at both sources is 1 p.u.
3.13 A single-line diagram of a three-phase power system is shown in Fig. 3.51. The ratings...

3.13 A single-line diagram of a three-phase power system is shown in Fig. 3.51. The ratings of the equipment are shown below Generator G: 100 MVA, 11 kV, Xi -X2-0.20 pu, Xo -0.05 pu Generator G2 : 100 MVA, 20 kV, Xi=X2=0.25 pu, Xo=0.03 pu, X,,-0.05 pu Transformer T: 100 MVA, 11/66 kV, Xi -X2-Xo 0.06 pu Transformer T2: 100 MVA, 11/66 kV, Xi-X2 = Xo 0.06 pu Line: 100 MVA, X,-X2 = 0.15 pu, Xo = 0.65 pu A...
3) The single-line diagram of a three-phase power system is shown in Fig. 1. Equipment ratings...

3) The single-line diagram of a three-phase power system is shown in Fig. 1. Equipment ratings are given as follows: G1 1,000 MVA, 15.0 kV, 20.18, o 0.07 pu G2 : 1,000 MVA. 15.0 kV, 攻=エ1 =エ2 = 0.20, ro = 0.10 pu G3 : 500 MVA, 13.8 kV. 1" = 띠 z2 = 0.15, zo 0.05 pu G4 : 750 MVA, 13.8 kV. ェd =ェ1 = 0.30, T2 = 0.40 ro = 0.10 pu Ti : 1,000 MVA. 15.0Δ/765Y...

the single-line diagram of a three-phase power system is shown in figure 9.17. equipment ratings are...

the single-line diagram of a three-phase power system is shown in figure 9.17. equipment ratings are given as follows: The inductor connected to Generator 3 neutral has a reactance of 0.05 per unit using generator 3 ratings as a base. Draw the zero-, positive-, and negative-sequence reactance diagrams using a 1000-MVA, 765-kV base in the zone of line 1-2. Neglect the Δ—Y. transformer phase shifts.