The beam shown is supported by a pin at A and rope BDE as shown. Knowing...

Question

Question

math Advanced-Math

Answer 1

Answer #1

soen IT T(A) 28(9-81) = 274.68N Let vestical and horizontal reaction at A are VA and HA respectively, And tension in rope BDE

Answer 2

Similar Homework Help Questions

The beam shown is supported by a pin at A and rope BDE as shown. Knowing...

The beam shown is supported by a pin at A and rope BDE as shown. Knowing that L = 1.2 m and that the mass suspended from C is 27 kg, determine the tension in rope BDE and the reactions at A. Enter the magnitude of the tension in rope BDE below, in N to the nearest whole N. (Take g = 9.81 m/s2) -2m-—2m-+
1) The uniform beam shown is supported by a pin at A and a light rope...

1) The uniform beam shown is supported by a pin at A and a light rope at B. A 1,000 lb weight is supported at C. Determine the normal force, shear force, and bending moment at point P. (15 p.) 30 3 А 2) The uniform beam shown is supported by a pin at and a roller at B. Using the analytical method (i.e., sections), construct the shear and moment diagrams. Write your equations V(x) and Mix) for each section...
rroviem . (32%) A 1-beam is supported by a ball-and-socket joint at A and a rope...

rroviem . (32%) A 1-beam is supported by a ball-and-socket joint at A and a rope at B. A horizontal force P = 300 lb is applied on the beam as shown. In addition, a load W is suspended from D. Determine the tension in the rope BC, the load W and the support reactions at A. 40 in d=30 in P-300 lb 20 in

1. The beam shown is supported by the pin at A and the cable CE a....

1. The beam shown is supported by the pin at A and the cable CE a. (5 points) Draw a free body diagram of the beamm b. (10 points) Find the tension in the cable. 5 m 8 m 4 m 3 m 150 N 450 N
A uniform 35.5-kg beam of length ℓ = 5.60 m is supported by a vertical rope...

A uniform 35.5-kg beam of length ℓ = 5.60 m is supported by a vertical rope located d = 1.20 m from its left end as in the figure below. The right end of the beam is supported by a vertical column. (a) Find the tension in the rope. (b) Find the force that the column exerts on the right end of the beam. (Enter the magnitude.)
A worker stands a distance d = 0.250 m from the left end of a beam as shown in the figure. The beam is supported by thre...

A worker stands a distance d = 0.250 m from the left end of a beam as shown in the figure. The beam is supported by three ropes. Find the tension in each rope (in N). Assume the beam is uniform, with length L = 2.00 m and mass 34.0 kg, and the weight of the worker is 710 N. (Due to the nature of this problem, do not use rounded intermediate values in your calculations—including answers submitted in WebAssign.)...

Problem 2. (32%) A I-beam is supported by a ball-and-socket joint at A and a rope...

Problem 2. (32%) A I-beam is supported by a ball-and-socket joint at A and a rope at B. A horizontal force P 300 lb is applied on the beam as shown. In addition, a load W is suspended from D. Determine the tension in the rope BC, the load W and the support 40 in d -30 in P-300 lb
The beam ABC has a mass of 78.0 kg and is supported by the rope BDC...

The beam ABC has a mass of 78.0 kg and is supported by the rope BDC that runs through the frictionless pulley at D. The winch at CC has a mass of 44.5 kg. The tension in the rope acts on the beam at points B and C and counteracts the moments due to the beam's weight (acting vertically at the midpoint of its length) and the weight of the winch (acting vertically at point C) such that the resultant...
The simply supported beam shown in Figure 1 is pin-supported at A and roller-supported at D....

The simply supported beam shown in Figure 1 is pin-supported at A and roller-supported at D. la) Replace the distributed loads in Figure 1 by an equivalent resultant force and locate its location with respect to A. {2 + 3 marks 1b) Calculate the reactions at supports A and D. {2 marks 1c) Calculate the shear force and bending moment at point C. {4 marks) 15 kN/m 6 kN/m D B q 3.0 m 3.0 m 3.0 m Figure 1

A beam is supported by a pin at A and a roller B. It is loaded...

A beam is supported by a pin at A and a roller B. It is loaded as shown. Determine the deflection at the midpoint (1/2) of the beam given the following: L = 17 ft M1 = 12 kip-ft M2 = 16 kip-ft E = 29,000 ksi 1 = 25 in i n Deflection at the midpoint (L/2) = Number Round answer to the nearest hundredth. Answer must include the proper sign (+/-).