In MATLAB how do you verify an answer? How do you create a
verification that includes a
report printed to the Command Window regarding the outcome of the
verification?
if the code is below how is the verification mentioned above achieved?
% Set of radii to check
r = 0:1:3;
% Volume of sphere
V = 4*pi*r.^3/3
% Set of radii to check
r = 0:1:3
% Volume of sphere
V = 4*pi*r.^3/3

so in order to calculate the relative error
that is difference between true and calculated values
just type abs( true_value - calculated value )
command abs will give absolute value that is positive value
In MATLAB how do you verify an answer? How do you create a verification that includes...
How do I solve using Matlab?
Use MATLAB to create a pattern such as the one below in the command window. Prompt the user to enter the max number of columns and number of intervals ran. In the left figure, the user selected 10 max columns and one interval. In the right figure, the user selected 5 max columns and two intervals. The program should run for n max columns and n number of intervals. **** ***** ***** *****
Nay
programming languge is fine (MatLab, Octave, etc.)
This is the whole document this last picture i sent is the
first page
5. Write and save a function Sphere Area that accepts Radius as input argument, and returns SurfaceArea (4 tt r) as output argument. Paste the function code below. Paste code here 6. Validate your Sphere Area function from the command line, checking the results against hand calculations. Paste the command line code and results below. 7. Design an...
Circuit Analysis: Need help writing this into MATLAB. I do not
need it in paper I need help putting it into MATLAB. * DO NOT WRITE
ON PAPER* Please use MATLAB and post your code. Thank you.
My work completed. Please help me in make code for the above
circuit ^.
Here is my work for Part 3 that is needed to complete this part
4. ( could not solve the last part)
Part 4. AC Solution by Phasor Analysis...
MATLAB Questions. I have a basic understanding of the tools for
MATLAB, but do not know how to create the code for these questions.
Please show the entire code.
2. A paper cup shaped as a frustum of cone with R-14R1 is designed to have a volume of 25 cm Determine R1, R2 and the surface area, S, of the paper for cups with a height, h, of 1O cm. The volume of the cup, V, and the surface area...
How
would i code this in MatLab
3. Write the program, openclasses.m, where you start by creating a structured array called class which contains the information in the following table (note: seats should be a single fieldname with a (1x2) array inside it). Class Title Introduction to Engineering Computers in Psychology Writing and Rhetoric Beginning Spanish Introduction to Africana Studies Number Seats (Max, Enrolled) 10111 (45, 32) 20000 (28, 25) 12100 (14, 14) 10101 (19,13) (36, 32) 20082 From this...
Could someone explain these four promblems on matlab and if you do,
could you write what you wrote on matlab I.e. on the command window
or script. Also if you have written anything by hand can you write
neatly. Also an explain of how you did it would be greatly
appreciated.
1] 5 points) Write the following set of equations in Matrix form and use Matlab to find the solution. 50 -5x3-6x2 2x2 + 7x3-30 x1-7x3-50-3x2 + 5x1 [2] (10...
This uses MATLAB code with plotting
HW19: Plotting with plot () Due 11:59 pm Monday 1. (10 pts) Write a script that will produce a sine curve and a cosine curve in the same plot, 0 as shown to the right. 06 0.4 0.2 To have two sets of data in one plot, you may plot the first one, then with the command hold on", plot the other. Or, you can learn how to plot two lines with just one...
yes you will need matlab software
Can someone please help me. attached is the exercise i am doing
in matlab. also attached is the exercise that i am suppose to be
doing.also attached is part a of my code and part b. also attached
is an error code i am getting. can someone please help me with
this. thanks. explain in detail what i am doing wrong and what i
need to do to fix it.
you use enogn polnts...
Matlab code 3. Create a units convertor for measures of volume. Ex: How many liters are in 10 gallons – answer is 37.8541. a. Create input statements that ask for a quantity and a set of possible units. The possible units are cubic meters, cubic feet, liters, or US gallons. b. Create an input statement to ask for the converted unit. c. Use if statements to perform the conversion. d. Use fprintf to display the conversion in a meaningful way...
MATLAB: If I have a vector for time and distance, how do I create a velocity vector? For example, T = [ 1; 2; 3; 4; ........] D = [ 2; 2; 3; 4; ........] and I need to find the velocity vector V = [] where the first value would be ((first value of D) / (first value of T)) Is there a way to create a loop for that and if so, what would be the code?