When comparing a water system we have a water circuit which is analogous to electric circuit.
Current flow in the electric circuit is similar to volumetric flow of water over time in water system..
Current flow is measured in amperes and volumetric flow with time is measured in gallons per minute..
So Given statement is TRUE...
Plzz give Positive Rating..Thanks
Compared to a water system, an ampere would be similar to a measure of water flow...
A flow rate meter is used to measure the flow rate of a water flow from left to right) in an inclined position. Due to spatial confinement, the two pressure taps-manometer tubes were inclined as well as shown. The meter is similar to a Venturi meter except at the small pipe the pressure tap is a stagnation pressure tap at 2. For the given geometries, calculate: 1) (4 pts)The velocity at the large pipe, in m/s 2) (3 pts)The velocity...
24 liters pf water per minute flow through a pipe 3cm in diameter.If that pipe widens into a 6 cm diameter pipe, how many liters per water flow through the larger pipe?
A water supply system draws from a river at an elevation of 800-feet and delivers the water to a storage reservoir at elevation 820-feet. The supply pipeline is a 1000-foot long, 10-inch diameter, cast iron pipe. A single pump with the pump characteristic curve in Figure 1 is used to fill the reservoir. Determine: a) Sketch the system described in the problem statement. b) Inlet and outlet minor loss coefficients, cite your source of minor loss coefficients. c) The roughness...
A Venturi flowmeter is used to measure the flow rate of water (see the figure below). The flowmeter is inserted in a water pipe that has a diameter of 2 cm. At the narrow section, the diameter of the pipe is 0.8 cm. The U-tube contains oil with density 0.85 g/cm3. If the difference in the oil level on the two sides of the flowmeter is 1.5 cm, what is the volume flow rate of water through the pipe? The...
Five gallons per minute of hot water at 180F and 20 psig is produced in a flow system by injection and condensation of low-pressure steam at 20 psig and 80% quality into cold water at 60F. The calculation basis is one minute. Calculate the steam mass flow rate in lbm/min; also calculate the exit pipe diameter if the velocity is to be maintained at 7ft/s.
The venturi flowmeter shown in the figure is used to measure the flow rate of water in a solar collector system. The flowmeter is inserted in a pipe with diameter 1.9 cm ; at the venturi of the flowmeter the diameter is reduced to 0.64 cm . The manometer tube contains oil with density 0.82 times that of water. If the difference in oil levels on the two sides of the manometer tube is 1.7 cm , what is the...
A Venturi meter equipped with a differential pressure gage is used to measure the flow rate of water at 15°C (p = 999.1 kg/m”) through a 5-cm- diameter horizontal pipe. The diameter of the Venturi neck is 3 cm, and the measured pressure drop is 5.1 kPa. Taking the discharge coefficient to be 0.98, determine the volume flow rate of water and the average velocity through the pipe. 5 cm 3 cm Differential pressure gage Is The volume flow rate...
Water flows in a pipe that has a 4 ft diameter and the following hypothetical velocity distribution: The velocity is maximum at the centerline and decreases linearly with r to a minimum at the pipe wall. If Vmax = 17 ft/s and Vmin = 10 ft/s, what is the discharge in cubic feet per second and in gallons per minute? The volume flow rate is given by the integral of the velocity over the area Using the correct expression for...
Water flows in a pipe that has a 4 ft diameter and the following hypothetical velocity distribution: The velocity is maximum at the centerline and decreases linearly with r to a minimum at the pipe wall. If Vmax = 15 ft/s and Vmin = 12 ft/s, what is the discharge in cubic feet per second and in gallons per minute? The volume flow rate is given by the integral of the velocity over the area Q = -fvaa Using the...
A flow nozzle equipped with a differential pressure gage is used to measure the flow rate of water at 10°C (p 9997 kg/m3 and p 1.307 x 10-3 kg/m s) through a 3-cm-diameter horizontal pipe. The nozzle exit diameter is 1.5 cm, and the measured pressure drop is 3.3 kPa. Determine the volume flow rate of water, the average velocity through the pipe, and the head loss 1.5 cm Differential pressure gage -3 m3(s m/s The volume flow rate of...