Question 3 8.3 M2 4 M2 M Vout = 788.5 mVp-p LF157A Given the Op-Amp above,...

Question

Question

Question 3 8.3 M2 4 M2 M Vout = 788.5 mVp-p LF157A Given the Op-Amp above, find Vin

engineering Electrical-Engineering

Answer 1

Answer #1

8.3 M2 44.52 w Rf Ri Vout Gain of inverting op amp -3 788.5x16 º - Vin - 8.3x106 4x106 Vinė – 2.075 Vin = 788.5 X6-3 -2.075

Answer 2

Similar Homework Help Questions

For this op Amp find the equation for the output voltage Vout in terms of input...

For this op Amp find the equation for the output voltage Vout in terms of input voltage Vin. (Ohms law, KVL, KCL) La Vin Q, Vout
Question 3 The following op-amp circuit is built. Determine Vout in terms of the component values...

Question 3 The following op-amp circuit is built. Determine Vout in terms of the component values shown and the characteristics of the typical 741 op-amp (Imax = 15 mA and A0 = 10") a) Is there a feedback path? +1.5 V vinnen b) Determine v-. -IV kums c) Determine vt. d) Determine lin. e) Determine lout f) Determine Vout g) Determine the gain. h) Given R1 = 3 kN and R2 = 9 kl, graph Vout for the following input....
C1 R1 U1 Vout Vin 1 The above integrator has a pole at 1Hz. Given R1-8㏀...

C1 R1 U1 Vout Vin 1 The above integrator has a pole at 1Hz. Given R1-8㏀ and G-8nF, find the open loop gain of the op amp.

Given the following Non-inverting op amp circuit. R3 Vout Vs 10k 10k What is the voltage...

Given the following Non-inverting op amp circuit. R3 Vout Vs 10k 10k What is the voltage at the op amp input terminal, V. ? A. V = OV B.V. = 20V C.V+ = 5V D.V+ = 10V QUESTION 4 Given the same circuit in Q3 What is the value of Vout? A. Vour = 60 V B. Vour-30V C.Vou - 5 D. Vour = 10V
Question 3 3 pts Focus on Op-amp U1 (Both op-amps have to be completely connected as...

Question 3 3 pts Focus on Op-amp U1 (Both op-amps have to be completely connected as shown in Figure A) Use myDAQ's oscilloscope to capture the input waveform Vin (on Channel 0) and the intermediate output waveform Vout1 (on Channel 1) superimposed. Set the amplitude scale for both channels of the oscilloscope to 500 mV/Div Set the time scale of the oscilloscope to 200 us/Div 1. Take a screenshot of the oscilloscope (both waveform in the same picture) and embed...
Inverting Amplifier Figure 4.2 shows the fundamental configuration of Op-Amp in which it is used as...

Inverting Amplifier Figure 4.2 shows the fundamental configuration of Op-Amp in which it is used as an inverting amplifier. In this configuration the ratio, R2/R1 completely controls the effective gain of the amplifier and it can be verified that the output voltage is equal to Vo = - (R2/R1)Vin R2 100K Q-10V R1 Vinow 20K 1 2 7 V Vo 3 -10v Figure 4.2 Part 1 - Inverting Amp: Procedure 1. Construct the circuit of figure 4.2 using Op-Amp IC...

An inverting op-amp is built using a 200 Ω input resistor and a 4 kΩ feedback...

An inverting op-amp is built using a 200 Ω input resistor and a 4 kΩ feedback resistor, with a supply of +/- 5V. Draw the circuit Calculate the gain for the op amp Calculate VOUT for the following VIN 0.1 V -2 V 0.05 V
A non-inverting amplifier using OP-amp is given in Figure Q4c. (8) Vout Vin 99 kN RL...

A non-inverting amplifier using OP-amp is given in Figure Q4c. (8) Vout Vin 99 kN RL 1 kQ AoL = 10s Figure Q4c Amplifier has the following properties. Open loop gain is 105 Open loop output impedance is 40 N Open loop bandwidth is 10 Hz Then, calculate The closed loop voltage gain. The closed loop output impedance. The closed loop bandwidth. i) ii) iii)
5. (10 Points) Using ideal op-amp assumptions, find Vout. 10Ω 4 Ω 6 Ω + Ε...

5. (10 Points) Using ideal op-amp assumptions, find Vout. 10Ω 4 Ω 6 Ω + Ε 3V 8 Ω 16Ω Vout 12 Ω

Prob. 4 2K2 Vin Iksal Vout Find ix, co, and is in the circuit. Assume an...

Prob. 4 2K2 Vin Iksal Vout Find ix, co, and is in the circuit. Assume an ideal Op Amp. Ike MU