Calculate values for the four resistors so that the amplifier circuit generates the given values for Ic, Vce and Ve
My Values for the question are
Ic = 3.8mA
Vce = 4.5v
Ve = 0.75v
How I can find Rb1, Rb2, Re and Rc?
Homework Answers
Request Answer!
12 have requested this problem solution
The more requests, the faster the answer.
Add Answer to:
Calculate values for the four resistors so that the amplifier circuit generates the given values for Ic, Vce and Ve
Calculate values for the four resistors so that the amplifier circuit generates the given values for Ic, Vce and Ve
IC=3.8mA, VCE=4.5V, VE=0.75
Vsig = 10mV*sin(2Kπ) The circuit above is a common-emitter amplifier. Given the parameters in the circuit,...
Vsig = 10mV*sin(2Kπ)
The circuit above is a common-emitter amplifier. Given the
parameters in the circuit,
1. If Rb1=10KΩ, Calculate Rb2, Ib, Ic, Ie, Re, transconductance
(gm), Current through Rb1 (I_rb1), and Current through Rb2(I_rb2),
Vb, Vc, Ve, Vce. Also, calculate Rc to achieve a voltage gain Av =
- 100 V/
(If Rb1 value does not match up, then choose your resistor
value for Rb1.)
2. If the amplitude of Vsig keeps increasing, at what amplitude
of the input...
Question 1 (4 points) Voc 3 Rc RB13 The voltage-divider bias circuit shown has Rc =...
Question 1 (4 points) Voc 3 Rc RB13 The voltage-divider bias circuit shown has Rc = 2 k12, RE = 400 12, RB1 = 300 k22, RB2 = 100 ks and Vcc = 25 V. Assume that VBE = 0.7 V and B = 90. Determine the Q- point (Ic and VCE) for the bias circuit. OVCE = 5.91 V Ic = 3.09 mA OVCE = 12.07 V Ic = 2.40 mA O VCE = 14.22 V Ic = 4.48...
Simplify the following BJT circuit using Thevenin's theorem, then find Is, IC, lE and VB, VCE....
Simplify the following BJT circuit using Thevenin's theorem, then find Is, IC, lE and VB, VCE. Given vcc-6 V, R1.50kS2, R2-30 kf2, RE-2 kS2, and RC-3.3 ㏀ and assume p-100.(show your workinthe Ri
a) Find the operating point (Ic and Vce) of the circuit shown in below. b) The...
a) Find the operating point (Ic and Vce) of the circuit shown in below. b) The BJT is biased at Ic = 1.5mA.Find the value of the VEE when all other parameters remain same I Vcc=5V + R 5k RA C- 260k PE=200 UT V26mV VB=0.7V -Ve=-2V
FIND THE VALUES OF Rb1, Rb2, Re,Rc, rin , rout, overall gain and open circuit gain First, design a common emitter BJT a...
FIND THE VALUES OF Rb1, Rb2, Re,Rc, rin , rout, overall gain and
open circuit gain
First, design a common emitter BJT amplifier Second, analyze the amplifier.( Avo, Gv, Rin, Rout) Third, compare your calculation with Multisim. Report must include comparison between your calculation & simulation results overall voltage gain, open circuit voltage gain, input resistance, and output resistance. This design project is not group work, must be done individually. Type your report. Design a discrete common emitter BJT amplifier.(Determine...
please choose one of the answer choices above. Must show all work, thank you Question 7...
please choose one of the answer choices above.
Must show all work, thank you
Question 7 CIRCUIT D1 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig. 7 (denoting the type Circuit C2). Assume the following: Vcc= 18 volt; VBE = 0.7; Rc = 1.5 k; RB2 = 33 k; Vc = 9.5 volt; Irc = 9.5 and, B = 100...
2. We will modify example 6.10 from the textbook during recitation #10 (11/14), by taking Re...
2. We will modify example 6.10 from the textbook during recitation #10 (11/14), by taking Re = 0, as shown in figure 2. When we make this modification, we will discover that the transistor will operate in saturation mode using the resistor values in example 6.10. ECE 342 Electronics I Homework # 10 Due Nov. 20, 2019 (Wednesday) a) Calculate the BJT terminal currents Ib, Ic and le, as well as the node voltages VB, Vc and Ve for Rsi...
please choose one of the answer choices above. Must show all work, thank you! Question 8...
please choose one of the answer choices above.
Must show all work, thank you!
Question 8 CIRCUIT D.2 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.8 (denoting the type Circuit D2). Assume the following: Vcc= 10 volt; VE = 1.8 volt; Rc = 2.0 k; RB2 = 25 k and a = 0.98958. +Vcc Rc IRC RB1 INIC 11 IB...
please choose one of the answer choices above. Must show all work, thank you Question 6...
please choose one of the answer choices above.
Must show all work, thank you
Question 6 CIRCUIT C2 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.6 (denoting the type Circuit C2). Assume the following: Vcc= 30 volt; Rc = 2.0 k; Roi = 15 k; RB2 = 7.5 k; ; RE = 2.0 k; VE = 9.3 volt; and, a=0.98684...
Vsig = 10mV*sin(2Kπ)
The circuit above is a common-emitter amplifier. Given the
parameters in the circuit,
1. If Rb1=10KΩ, Calculate Rb2, Ib, Ic, Ie, Re, transconductance
(gm), Current through Rb1 (I_rb1), and Current through Rb2(I_rb2),
Vb, Vc, Ve, Vce. Also, calculate Rc to achieve a voltage gain Av =
- 100 V/
(If Rb1 value does not match up, then choose your resistor
value for Rb1.)
2. If the amplitude of Vsig keeps increasing, at what amplitude
of the input...
Question 1 (4 points) Voc 3 Rc RB13 The voltage-divider bias circuit shown has Rc = 2 k12, RE = 400 12, RB1 = 300 k22, RB2 = 100 ks and Vcc = 25 V. Assume that VBE = 0.7 V and B = 90. Determine the Q- point (Ic and VCE) for the bias circuit. OVCE = 5.91 V Ic = 3.09 mA OVCE = 12.07 V Ic = 2.40 mA O VCE = 14.22 V Ic = 4.48...
Simplify the following BJT circuit using Thevenin's theorem, then find Is, IC, lE and VB, VCE. Given vcc-6 V, R1.50kS2, R2-30 kf2, RE-2 kS2, and RC-3.3 ㏀ and assume p-100.(show your workinthe Ri
a) Find the operating point (Ic and Vce) of the circuit shown in below. b) The BJT is biased at Ic = 1.5mA.Find the value of the VEE when all other parameters remain same I Vcc=5V + R 5k RA C- 260k PE=200 UT V26mV VB=0.7V -Ve=-2V
FIND THE VALUES OF Rb1, Rb2, Re,Rc, rin , rout, overall gain and
open circuit gain
First, design a common emitter BJT amplifier Second, analyze the amplifier.( Avo, Gv, Rin, Rout) Third, compare your calculation with Multisim. Report must include comparison between your calculation & simulation results overall voltage gain, open circuit voltage gain, input resistance, and output resistance. This design project is not group work, must be done individually. Type your report. Design a discrete common emitter BJT amplifier.(Determine...
please choose one of the answer choices above.
Must show all work, thank you
Question 7 CIRCUIT D1 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig. 7 (denoting the type Circuit C2). Assume the following: Vcc= 18 volt; VBE = 0.7; Rc = 1.5 k; RB2 = 33 k; Vc = 9.5 volt; Irc = 9.5 and, B = 100...
2. We will modify example 6.10 from the textbook during recitation #10 (11/14), by taking Re = 0, as shown in figure 2. When we make this modification, we will discover that the transistor will operate in saturation mode using the resistor values in example 6.10. ECE 342 Electronics I Homework # 10 Due Nov. 20, 2019 (Wednesday) a) Calculate the BJT terminal currents Ib, Ic and le, as well as the node voltages VB, Vc and Ve for Rsi...
please choose one of the answer choices above.
Must show all work, thank you!
Question 8 CIRCUIT D.2 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.8 (denoting the type Circuit D2). Assume the following: Vcc= 10 volt; VE = 1.8 volt; Rc = 2.0 k; RB2 = 25 k and a = 0.98958. +Vcc Rc IRC RB1 INIC 11 IB...
please choose one of the answer choices above.
Must show all work, thank you
Question 6 CIRCUIT C2 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.6 (denoting the type Circuit C2). Assume the following: Vcc= 30 volt; Rc = 2.0 k; Roi = 15 k; RB2 = 7.5 k; ; RE = 2.0 k; VE = 9.3 volt; and, a=0.98684...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago