Homework Answers
Add Answer to:
Exercise#2 • An AC supply of 230V rms is applied to a half wave rectifier circuit...
A) Draw the circuit diagram and design a half wave rectifier AC-DC converter to deliver 12V-DC...
A) Draw the circuit diagram and design a half wave rectifier AC-DC converter to deliver 12V-DC with a ripple of 10 mV for a load current of 0.5 A - Design means to find the capacitor value and the ratio of the turns in the transformer assuume the supply voltage is 120v and 60Hz B) Calculate the Peak Inverse Voltage, average and max current through the diode.
A half-wave rectifier has a 120 Vrms 60 HZ ac source. The load IS 50...
Q1)A half-wave rectifier has a 120 Vrms 60 HZ ac source. The load IS 50 W. Determine the value of a filter capacitor to keep the peak-to-peak nipple across the load to less than 1.5V. Seled the one best answer from the choices given below(a) 410 UF (d) 3270 uF (b) 820 UF (e) 6540 UFQ2)A diode whose internal resistance is 200 is to supply power to a 1000 load from 110V (rms) source pf supply. Calculate(a) peak load current...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
6.26. Calculate the average power delivered to the load for the full-wave bridge rectifier circuit in...
6.26. Calculate the average power delivered to the load for the full-wave bridge rectifier circuit in Figure 6.9 if the diode is ideal, Vac is sinusoidal with a peak value of 170 V, and the load resistor has a value of 100 12. AC D4 -DC 4 +DC 4 D AC RL FIGURE 6.9 Full-wave bridge rectifier circuit.
A half-wave rectifier circuit with a 500-Q load operates from a 120-V (rms) 60-Hz household supply...
A half-wave rectifier circuit with a 500-Q load operates from a 120-V (rms) 60-Hz household supply through a 12-to-l step-down transformer. It uses a silicon diode that can be modeled to have a 0.7-V drop for any current. What is the peak voltage of the rectified output? For what fraction of the cycle does the diode conduct? What is the average output voltage? What is the average current in the load. please do not copy answers from others.
D *4.80 It is required to use a peak rectifier to design a de power supply...
D *4.80 It is required to use a peak rectifier to design a de power supply that provides an average de output voltage of 12 V on which a maximum of ±1-V ripple is allowed. The rectifier feeds a load of 200 2. The rectifier is fed from the line voltage (120 V rms, 60 Hz) through a transformer. The diodes available have 0.7-V drop when conducting. If the designer opts for the half-wave circuit: (a) Specify the rms voltage...
A half-wave diode rectifier circuit is driven by a 60Hz sine wave with a peak value...
A half-wave diode rectifier circuit is driven by a 60Hz sine wave with a peak value of 19V. If the load resistance this circuit drives is 4.3kΩ and the ripple voltage at the output is 0.43 Vpeak-to-peak, then what is the peak current in the diode in milliamps? Answer: Check The diode circuit shown is a Select one: O a. Voltage doubler circuit O b. DC restorer circuit c. Limiter circuit O d. Peak detector circuit O e. None of...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliv...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
Problem 3 (40 points): A single-phase half-wave rectifier shown in the following figure has a pure...
Problem 3 (40 points): A single-phase half-wave rectifier shown in the following figure has a pure resistive load of RL112. Assume Vm 311V, f- 60Hz. (1) Determine the efficiency, the FF, the RF, the TUF, the PIV of the diode, the CF of the input currernt and the input PF (2) Design a C-filter so that the ripple factor of the output voltage is less than 5%; (3) With the value of capacitor C determined from (2), calculate the average...
Figure 2 shows a power supply circuit comprising a transformer coupling the mains voltage on the...
Figure 2 shows a power supply circuit comprising a transformer coupling the mains voltage on the left to the full-wave rectifier circuit on the right. It is given that the mains voltage (Vmains) is 230 V RMS, the mains frequency (fin) is 50 Hz, the transformer T1 has a ratio of 9:1, the load resistance (RL) is 1 k. and the capacitance of the capacitor (C) is 470 uF. a. Calculate the following: 1. the transformer AC output RMS voltage...
Q1)A half-wave rectifier has a 120 Vrms 60 HZ ac source. The load IS 50 W. Determine the value of a filter capacitor to keep the peak-to-peak nipple across the load to less than 1.5V. Seled the one best answer from the choices given below(a) 410 UF (d) 3270 uF (b) 820 UF (e) 6540 UFQ2)A diode whose internal resistance is 200 is to supply power to a 1000 load from 110V (rms) source pf supply. Calculate(a) peak load current...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will:
Take 120volts ac, 60 hz, sinusoidal waveform and convert
it to a “regulated “dc value
giving 12 volts +, - 1 volt across a 2000-ohm output
load resistor with no more than 2%
ripple voltage.
You may assume:
a. An ideal power transformer as discussed in class.
b. For hand computations, you must assume a diode given by
Figure 4.8 page 185.
c. A filter capacitor sized per the textbook equation...
6.26. Calculate the average power delivered to the load for the full-wave bridge rectifier circuit in Figure 6.9 if the diode is ideal, Vac is sinusoidal with a peak value of 170 V, and the load resistor has a value of 100 12. AC D4 -DC 4 +DC 4 D AC RL FIGURE 6.9 Full-wave bridge rectifier circuit.
D *4.80 It is required to use a peak rectifier to design a de power supply that provides an average de output voltage of 12 V on which a maximum of ±1-V ripple is allowed. The rectifier feeds a load of 200 2. The rectifier is fed from the line voltage (120 V rms, 60 Hz) through a transformer. The diodes available have 0.7-V drop when conducting. If the designer opts for the half-wave circuit: (a) Specify the rms voltage...
A half-wave diode rectifier circuit is driven by a 60Hz sine wave with a peak value of 19V. If the load resistance this circuit drives is 4.3kΩ and the ripple voltage at the output is 0.43 Vpeak-to-peak, then what is the peak current in the diode in milliamps? Answer: Check The diode circuit shown is a Select one: O a. Voltage doubler circuit O b. DC restorer circuit c. Limiter circuit O d. Peak detector circuit O e. None of...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
Problem 3 (40 points): A single-phase half-wave rectifier shown in the following figure has a pure resistive load of RL112. Assume Vm 311V, f- 60Hz. (1) Determine the efficiency, the FF, the RF, the TUF, the PIV of the diode, the CF of the input currernt and the input PF (2) Design a C-filter so that the ripple factor of the output voltage is less than 5%; (3) With the value of capacitor C determined from (2), calculate the average...
Figure 2 shows a power supply circuit comprising a transformer coupling the mains voltage on the left to the full-wave rectifier circuit on the right. It is given that the mains voltage (Vmains) is 230 V RMS, the mains frequency (fin) is 50 Hz, the transformer T1 has a ratio of 9:1, the load resistance (RL) is 1 k. and the capacitance of the capacitor (C) is 470 uF. a. Calculate the following: 1. the transformer AC output RMS voltage...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 11 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 11 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 11 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 11 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 11 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 11 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 11 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 11 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 11 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 11 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 11 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 11 months ago