Three pipes are in parallel configuration with a total head loss of 20.3 m. The pipe...
Three pipes are in parallel configuration with a total head loss of 20.3 m. The pipe data are:
| Pipe | L (m) | D (m) | Absolute roughness (mm) | Relative roughness (Absolute roughness / D) |
|---|---|---|---|---|
| 1 | 100 | 0.08 | 0.24 | 0.003 |
| 2 | 150 | 0.06 | 0.12 | 0.002 |
| 3 | 80 | 0.04 | 0.20 | 0.005 |
Use density = 1000 kg/m^3 and kinematic viscosity = 1.02 x 10^-6
m^2/s. Calculate the total flow rate. Neglect any minor
losses.
Show the working all the way to the final answer ΣQ = 0.02772 m^3/s
.
Homework Answers
Add Answer to:
Three pipes are in parallel configuration with a total head loss
of 20.3 m. The pipe...
C= 20 L/S 3. Neglecting minor losses in the pipe, determine the flows in the pipes...
C= 20 L/S
3. Neglecting minor losses in the pipe, determine the flows in the pipes and the pressure heads at the nodes (kinematic viscosity= 1.13x10 mº/s). Lengths and diameters of pipes are given in the table below. Roughness size of all pipes is 0.06 mm. Pressure head elevation at A point is 65 m od and the elevations of pipe nodes from A to F are 30, 25,20, 20, 22, and 25, respectively BE Pipe Length m) Diameter (mm)...
Atwood Machine Data M=5883kg M2= 5874kg mr 0086kg M M Accel Rider .02 .04 .06 .08...
Atwood Machine Data M=5883kg M2= 5874kg mr 0086kg M M Accel Rider .02 .04 .06 .08 .1 Avg. Accel .1623 .3261 -.4732 .6286 .7652 (M2) Mass Ratio .0166 .0326 .0482 .0633 .0779 (M,+my+m.)s Acceleration vs. Mass Ratio 08 0.6 Acceleration (m/s) 0.4 02 0 o 0.02 0.08 0.1 0.04 0.06 Mass Ratio • When the system is put into motion, the velocity vs. time graph that was obtained is below. Given this graph, describe the motion of the falling mass....
Q2 (12): Th and parallel pipes BC and BD. The head loss between the lower reservoir...
Q2 (12): Th and parallel pipes BC and BD. The head loss between the lower reservoir and the pump can be ignored. The Darcy friction factor of each pipe is f 0.022. If the flow in pipe AB is 0.20 m'/s and AZ is 10.4 m, determine the total head of pump. What is daily power input (in the unit of Kw-hr) if the pump is running at 80% efficiency? e system shown in the following figure consists of two...
Consider a 100 mm internal diameter plastic pipe with a length of 1000 m and an...
Consider a 100 mm internal diameter plastic pipe with a length of 1000 m and an absolute roughness of 0.01 mm. Assume the kinematic viscosity of water to be 1.14 mm2/s. a) What should the secondary loss coefficient k be to have a secondary loss one tenth of the friction loss at Re = 4000? [41] b) Calculate the friction, secondary and total head losses for the pipe at a Re = 105. Use the secondary loss coefficient found in...
6. (25 points) Water at standard atmospheric conditions flows through a 100 m long plastic pipe...
6. (25 points) Water at standard atmospheric conditions flows through a 100 m long plastic pipe with a circular cross section of diameter D = 0.2 m at an average velocity of 10 cm/s. The flow exits into the atmosphere. The pipe material is smooth and has essentially no roughness. What is the pressure at the pipe entrance if it is horizontal? What is the pressure at the pipe entrance if the elevation increases by 50 cm? A Moody diagram...
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at...
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at an elevation 10 m above the reservoir surface. The mass flow rate is 40 kg/s and the volumetric flow rate is 0.040 m3/s. The large diameter inlet pipe total length is 50 m. The pump effidency is 65%. The longer smaller diameter pipe leaving the pump is 200 m in total length. The pipes have different diameters as indicated below. The...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...
For the three connected reservoirs with the given information, calculate the water velocity in each pipe,...
For the three connected reservoirs with the given information, calculate the water velocity in each pipe, neglecting the minor losses Patm Zв 850 f. =700 ft. d 1.1 ft Patm =800 ft. d 1 ft f=0.03 atm in all pipes ZA838 ft. d 1.2 ft =600 ft =805 ft. Datum F (velocity, ft/s x diameter. (Vd) for water at 6 Valu 8000 8 10 0.1 0.2 0.4 0.6 0.8 1 40 60 80 100 200 400 600 800 1000 2...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis 250 250 200 Stress (MPa) Stress (MPa) 150 $150 100 100 0 0 0 0.02 0.04 0.06 0.12 0.14 0.16 0.18 0 0.08 0.1 Strain 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01 Strain (a) Determine the % elongation, yield stress and ultimate tensile strength of the material tested above (3 marks) (b) Calculate the elastic modulus of the material tested above...
Temperature Density °C kg/m3 0 999.82 5 1000.00 10 999.77 15 999.19 20 998.29 25 997.13...
Temperature Density °C kg/m3 0 999.82 5 1000.00 10 999.77 15 999.19 20 998.29 25 997.13 30 995.71 35 994.08 40 992.25 45 990.22 50 988.02 55 985.65 60 983.13 65 980.45 70 977.63 75 974.68 80 971.60 85 968.39 90 965.06 95 961.62 100 958.05 Dynamic viscosity kg/m.s 0.0017920 0.0015200 0.0013080 0.0011390 0.0010030 0.0008910 0.0007980 0.0007200 0.0006530 0.0005960 0.0005470 0.0005040 0.0004670 0.0004340 0.0004040 0.0003780 0.0003550 0.0003340 0.0003150 0.0002980 0.0002820 Kinematic viscosity mºs x 10-6 1.7923226 1.5200000 1.3083009 1.1399233 1.0047181...
C= 20 L/S
3. Neglecting minor losses in the pipe, determine the flows in the pipes and the pressure heads at the nodes (kinematic viscosity= 1.13x10 mº/s). Lengths and diameters of pipes are given in the table below. Roughness size of all pipes is 0.06 mm. Pressure head elevation at A point is 65 m od and the elevations of pipe nodes from A to F are 30, 25,20, 20, 22, and 25, respectively BE Pipe Length m) Diameter (mm)...
Atwood Machine Data M=5883kg M2= 5874kg mr 0086kg M M Accel Rider .02 .04 .06 .08 .1 Avg. Accel .1623 .3261 -.4732 .6286 .7652 (M2) Mass Ratio .0166 .0326 .0482 .0633 .0779 (M,+my+m.)s Acceleration vs. Mass Ratio 08 0.6 Acceleration (m/s) 0.4 02 0 o 0.02 0.08 0.1 0.04 0.06 Mass Ratio • When the system is put into motion, the velocity vs. time graph that was obtained is below. Given this graph, describe the motion of the falling mass....
Q2 (12): Th and parallel pipes BC and BD. The head loss between the lower reservoir and the pump can be ignored. The Darcy friction factor of each pipe is f 0.022. If the flow in pipe AB is 0.20 m'/s and AZ is 10.4 m, determine the total head of pump. What is daily power input (in the unit of Kw-hr) if the pump is running at 80% efficiency? e system shown in the following figure consists of two...
6. (25 points) Water at standard atmospheric conditions flows through a 100 m long plastic pipe with a circular cross section of diameter D = 0.2 m at an average velocity of 10 cm/s. The flow exits into the atmosphere. The pipe material is smooth and has essentially no roughness. What is the pressure at the pipe entrance if it is horizontal? What is the pressure at the pipe entrance if the elevation increases by 50 cm? A Moody diagram...
8-C) As shown below water is pumped and sprayed through a nozzle into the atmosphere at 20 m/s at an elevation 10 m above the reservoir surface. The mass flow rate is 40 kg/s and the volumetric flow rate is 0.040 m3/s. The large diameter inlet pipe total length is 50 m. The pump effidency is 65%. The longer smaller diameter pipe leaving the pump is 200 m in total length. The pipes have different diameters as indicated below. The...
A centrifugal pump test yields the following data: Pump Head Flow (m)(L/min) 30 25 20 40 The pump curve can be approximated by a parabola. This pump draws water from a large reservoir. The discharge of the pump feeds 150 m of 1.5 cm inside diameter pipe and then 225 m of 3 cm inside diameter pipe.. The two pipes both have a roughness of 0.5 mm The 3 cm pipe discharges to atmosphere a distance 40 m below the...
For the three connected reservoirs with the given information, calculate the water velocity in each pipe, neglecting the minor losses Patm Zв 850 f. =700 ft. d 1.1 ft Patm =800 ft. d 1 ft f=0.03 atm in all pipes ZA838 ft. d 1.2 ft =600 ft =805 ft. Datum F (velocity, ft/s x diameter. (Vd) for water at 6 Valu 8000 8 10 0.1 0.2 0.4 0.6 0.8 1 40 60 80 100 200 400 600 800 1000 2...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis 250 250 200 Stress (MPa) Stress (MPa) 150 $150 100 100 0 0 0 0.02 0.04 0.06 0.12 0.14 0.16 0.18 0 0.08 0.1 Strain 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01 Strain (a) Determine the % elongation, yield stress and ultimate tensile strength of the material tested above (3 marks) (b) Calculate the elastic modulus of the material tested above...
Temperature Density °C kg/m3 0 999.82 5 1000.00 10 999.77 15 999.19 20 998.29 25 997.13 30 995.71 35 994.08 40 992.25 45 990.22 50 988.02 55 985.65 60 983.13 65 980.45 70 977.63 75 974.68 80 971.60 85 968.39 90 965.06 95 961.62 100 958.05 Dynamic viscosity kg/m.s 0.0017920 0.0015200 0.0013080 0.0011390 0.0010030 0.0008910 0.0007980 0.0007200 0.0006530 0.0005960 0.0005470 0.0005040 0.0004670 0.0004340 0.0004040 0.0003780 0.0003550 0.0003340 0.0003150 0.0002980 0.0002820 Kinematic viscosity mºs x 10-6 1.7923226 1.5200000 1.3083009 1.1399233 1.0047181...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago