QUESTION 8 10 points In a hydraulic jack, a force F is applied to the small...

Question

Question

engineering Civil-Engineering

Answer 1

Answer #1

hleight to be lted In hydsoulic Jack l048 F-173.396

Answer 2

Similar Homework Help Questions

A hydraulic jack is made with a small piston 1.4 cm in diameter that is used...

A hydraulic jack is made with a small piston 1.4 cm in diameter that is used to move a large piston 5.3 cm in diameter. If a man can exert a force of 400 N on the small piston, how heavy a load can he lift with the jack?
a force of 227N is applied to a hydraulic jack piston that is 0.0250m in diameter....

a force of 227N is applied to a hydraulic jack piston that is 0.0250m in diameter. the piston supporting the load has a diameter of 0.175m (ignore any difference in height between the two pistons) a. what is the magnitude of the output force (N) on the hydraulic jack? b. how much mass (kg) can be lifted by the jack?
The small piston of a hydraulic lift has a diameter of 8.0 cm, and large piston...

The small piston of a hydraulic lift has a diameter of 8.0 cm, and large piston has a diameter of 40 cm. The lift raises a load of 15,000 N. Determine the force that must be applied to the small piston. Determine the pressure applied to the fluid in the lift.

2. The input and output pistons of a hydraulic jack are 4 cm and 12 cm...

2. The input and output pistons of a hydraulic jack are 4 cm and 12 cm in diameter. If a lever has a mechanical advantage of 9 and applied 200 Nof force on the input piston, how many pounds can the jack lift at 75% efficiency? 200 N of Force "MA" 9 12cm ? Newtons 4cm
6. A hydraulic lift system has a small piston (r = 10 cm) and a large...

6. A hydraulic lift system has a small piston (r = 10 cm) and a large piston (r = 40 cm). If the force applied to the small piston is 515 N, what is the force exerted by the large piston? If the small piston moves 6 cm, how far does the large piston move? Make sure to draw a diagram of the system.
he small piston of a hydraulic lift has a cross-sectional area of 3.50 cm2, and its...

he small piston of a hydraulic lift has a cross-sectional area of 3.50 cm2, and its large piston has a cross-sectional area of 200.0 cm2 (please see the figure below). What force must be applied to the small piston for the lift to raise a load of 14.8 kN? (In service stations, this force is usually exerted by compressed air.)

b) A hydraulic press (Figure 4) has a small and large piston with diameter of 50...

b) A hydraulic press (Figure 4) has a small and large piston with diameter of 50 mm and 400 mm, respectively. i) Calculate the force (F2) required to hold the weight of container when the force applied at the small piston is 800 N and both pistons are at the same elevation (h=0). [7 Marks) i) w Compare and discuss the force with pat b () if the height has been lifted three meters. Support your answer with calculations. [5...
the page 3 8) The area of the large piston in a hydraulic jack is 4.75...

the page 3 8) The area of the large piston in a hydraulic jack is 4.75 in 2. The area of the small piston is o.s64 in.2 what force wust be applied to the small piston if a weight of 2000 lb is to be lifted? what is the mechanical advantage MA 19) A monkey lifts ss lbs of water one foot in one second from a well 120 ft. deep. if electricity costs 13 cents per Kilowatt"hour, how much...
A hydraulic jack is designed to lift a car by exerting an output force 100 times...

A hydraulic jack is designed to lift a car by exerting an output force 100 times as large as the input. (a) What must be the ratio of the cylinder diameter on the output side to that on the input side? (b) If the input side is pushed down by 10 cm, how much does the output side move up? (The fluid volume loss on the input side is gained on the output side.) (c) Show that the work we...

LEARN MORE REMARKS In this problem, we didn't address the effect of possible differences in the...

LEARN MORE REMARKS In this problem, we didn't address the effect of possible differences in the helghts of the pistons. If the column of fluid is higher in the small piston, the fluid weight assists in supporting the car, reducing the necessary applied force. If the column of fluid is higher in the large piston, both the car and the extra fluid must be supported, so additional applied force is required. QUESTION if the radius of the output piston is...