Homework Answers
Add Answer to:
how you do this qn plz
A beam is made from a linear elastic material and...
Answer: y = 138.889 mm from bottom IXX = 282.115×106 mm4 9. Establish the height of the centroid in 300mm the concrete...
Answer:
y = 138.889 mm from bottom
IXX = 282.115×106 mm4
9. Establish the height of the centroid in 300mm the concrete beam section shown and calculate the second moment of area about the centroidal axis, lo, (in mm*) using the general formula: Hint: The width of the trapezoid at a general height, y (measured from the neutral axis) is described by the expression: 150mm b (300-150) y 250 Fig. Q9 where b is the width of the section at...
A beam with a cross section shown below is subjected to a positive moment about a horizontal axis...
A beam with a cross section shown below is subjected to a positive moment about a horizontal axis. The beam is made from an elastic perfectly plastic material with an allowable yield stress of 220 MPa. "t" has a value of 12 mm. Answer the questions that follow: 10t 6t Determine the centroid of this section i.e.as measured from the bottom of the section in [mm) - Determine the moment of inertia about the elastic neutral axis in [mm4] Determine...
4. (30%) For a beam with a T-section as shown, the cross-sectional dimensions of 12 mm....
4. (30%) For a beam with a T-section as shown, the cross-sectional dimensions of 12 mm. The centroid is 75 mm, h = 90 mm, t the beam are b 60 mm, h, at C and c 30 mm. At a certain section of the beam, the bending moment is M 5.4 kN m and the vertical shear force is V= 30 kN. (a) Show that the moment of inertia of the cross-section about the z axis (the neutral axis)...
3) (35 pts) A L-beam has the cross section shown. A moment M acts about the...
3) (35 pts) A L-beam has the cross section shown. A moment M acts about the x-axis which passes through the centroid of the section. Determine the angle the neutral axis makes with respect to axis. Sketch it on the cross section. Given the design flexural stress limit is 100 MPa, determine the maximum allowable moment which can be applied. You only need to evaluate the stresses at points A, B. Helpful hint: Remember to change the sign of your...
QUESTION 11 Knowing that for the extruded beam shown in the figure below, the allowable stress...
QUESTION 11 Knowing that for the extruded beam shown in the figure below, the allowable stress is 120 MPa in tension and 150 MPa in compression. 125 mm N-A 50 mm 125 mm 150 mm The centroid () measured from bottom of cross-section is: [mm.] 114.7 138.25 151.32 163.17 NI QUESTION 12 The moment of inertia () around neutral axis (N.A.) is: [m 122.16x 10 5 165.56x 10 5 212.45x 10 6 310.11x 10 5
An I-beam has a flange width b = 200 mm , height h = 200 mm , web thickness tw = 8 mm , and flange thickness tf = 12 mm...
An I-beam has a flange width b = 200 mm , height h = 200 mm ,
web thickness tw = 8 mm , and flange thickness
tf = 12 mm . Use the following steps to calculate the
shear stress at a point 65 mm above the neutral axis.
Part A - Moment of inertia
The shear formula includes the moment of inertia of the whole
cross section, I, about the neutral axis. Calculate the moment of
inertia.
Express...
V = 118 KN A beam with the cross-section shown is carrying a vertical shear force...
V = 118 KN
A beam with the cross-section shown is carrying a vertical shear force of magnitude v. 15mm It has already been calculated that: the neutral plane is 29 mm above the bottom face, and the second moment of area is / = 8.121x107 m (you do not need to re-calculate these values), NP7 29mn 28m mm Isom a) Indicate on the drawing above, where the shear stress () in the beam will be the greatest? b) Calculate...
Consider the box section in Figure 2. Assume that the skin/webs of the structure are fully effective in resisting direct stresses do the following: a) Idealise the continuous structure to one with boo...
Consider the box section in Figure 2. Assume that the skin/webs
of the structure are fully effective in resisting direct stresses
do the following: a) Idealise the continuous structure to one with
booms of the concentrated area and zero thickness shear webs. (Use
5 booms on the top and bottom; 3 booms on left and right sides) b)
Calculate Ixx, Iyy, Ixy for the section c) For a shear load of 120
KN applied coincident with the front vertical web,...
Q1. Determine the plastic moment of a steel beam made of elastoplastic material. The beam cross-section...
Q1. Determine the plastic moment of a steel beam made of elastoplastic material. The beam cross-section is shown in the figure below. The yield strength of the material is 240 MPa. Q1(a). Determine the distance of neutral axis in mm (the distance y bar) from the bottom of the cross-section. The distance y bar is shown in Q1(b). Q1(b). The cross-section of the beam is divided according to the areas shown in the figure below Determine the resultant force R1...
Question 1: A beam made of cast iron is fixed to a rigid wall on the...
Question 1: A beam made of cast iron is fixed to a rigid wall on the left end. Yield strength of the cast iron is 270 MPa. At the right free end, an axial tensile force P is applied along the middle bottom of the beam, as shown in the following figure. Its cross section is an equilateral triangle with h=13 mm (note h #b for the triangle). The moment of inertia for the triangle is shown by the formula...
Answer:
y = 138.889 mm from bottom
IXX = 282.115×106 mm4
9. Establish the height of the centroid in 300mm the concrete beam section shown and calculate the second moment of area about the centroidal axis, lo, (in mm*) using the general formula: Hint: The width of the trapezoid at a general height, y (measured from the neutral axis) is described by the expression: 150mm b (300-150) y 250 Fig. Q9 where b is the width of the section at...
A beam with a cross section shown below is subjected to a positive moment about a horizontal axis. The beam is made from an elastic perfectly plastic material with an allowable yield stress of 220 MPa. "t" has a value of 12 mm. Answer the questions that follow: 10t 6t Determine the centroid of this section i.e.as measured from the bottom of the section in [mm) - Determine the moment of inertia about the elastic neutral axis in [mm4] Determine...
4. (30%) For a beam with a T-section as shown, the cross-sectional dimensions of 12 mm. The centroid is 75 mm, h = 90 mm, t the beam are b 60 mm, h, at C and c 30 mm. At a certain section of the beam, the bending moment is M 5.4 kN m and the vertical shear force is V= 30 kN. (a) Show that the moment of inertia of the cross-section about the z axis (the neutral axis)...
3) (35 pts) A L-beam has the cross section shown. A moment M acts about the x-axis which passes through the centroid of the section. Determine the angle the neutral axis makes with respect to axis. Sketch it on the cross section. Given the design flexural stress limit is 100 MPa, determine the maximum allowable moment which can be applied. You only need to evaluate the stresses at points A, B. Helpful hint: Remember to change the sign of your...
QUESTION 11 Knowing that for the extruded beam shown in the figure below, the allowable stress is 120 MPa in tension and 150 MPa in compression. 125 mm N-A 50 mm 125 mm 150 mm The centroid () measured from bottom of cross-section is: [mm.] 114.7 138.25 151.32 163.17 NI QUESTION 12 The moment of inertia () around neutral axis (N.A.) is: [m 122.16x 10 5 165.56x 10 5 212.45x 10 6 310.11x 10 5
An I-beam has a flange width b = 200 mm , height h = 200 mm ,
web thickness tw = 8 mm , and flange thickness
tf = 12 mm . Use the following steps to calculate the
shear stress at a point 65 mm above the neutral axis.
Part A - Moment of inertia
The shear formula includes the moment of inertia of the whole
cross section, I, about the neutral axis. Calculate the moment of
inertia.
Express...
V = 118 KN
A beam with the cross-section shown is carrying a vertical shear force of magnitude v. 15mm It has already been calculated that: the neutral plane is 29 mm above the bottom face, and the second moment of area is / = 8.121x107 m (you do not need to re-calculate these values), NP7 29mn 28m mm Isom a) Indicate on the drawing above, where the shear stress () in the beam will be the greatest? b) Calculate...
Consider the box section in Figure 2. Assume that the skin/webs
of the structure are fully effective in resisting direct stresses
do the following: a) Idealise the continuous structure to one with
booms of the concentrated area and zero thickness shear webs. (Use
5 booms on the top and bottom; 3 booms on left and right sides) b)
Calculate Ixx, Iyy, Ixy for the section c) For a shear load of 120
KN applied coincident with the front vertical web,...
Q1. Determine the plastic moment of a steel beam made of elastoplastic material. The beam cross-section is shown in the figure below. The yield strength of the material is 240 MPa. Q1(a). Determine the distance of neutral axis in mm (the distance y bar) from the bottom of the cross-section. The distance y bar is shown in Q1(b). Q1(b). The cross-section of the beam is divided according to the areas shown in the figure below Determine the resultant force R1...
Question 1: A beam made of cast iron is fixed to a rigid wall on the left end. Yield strength of the cast iron is 270 MPa. At the right free end, an axial tensile force P is applied along the middle bottom of the beam, as shown in the following figure. Its cross section is an equilateral triangle with h=13 mm (note h #b for the triangle). The moment of inertia for the triangle is shown by the formula...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago