Question

Some household appliances have plugs with two prongs while others have three prongs. The additional prong...

Some household appliances have plugs with two prongs while others have three prongs. The additional prong is

for additional mechanical strength.

for 240-Hz voltage.

to connect to ground.

for 120-Hz voltage.

for direct current.

0 0
Add a comment Improve this question
Answer #1

The additional putting is to connect to ground.

Some appliances might get short circuit, or have some charge leakage from the circuit to the body of the appliance. When you touch these appliances the charge flows through you and give you a shock, in some cases shocks could be lethal. To prevent this, manufacturers provides an alternative route for the charges to flow directly to the ground via the third prong.

Add a comment
Know the answer?
Add Answer to:
Some household appliances have plugs with two prongs while others have three prongs. The additional prong...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • 1. [20 Pts] You are given the data-path below. Note that there are three registers. Two of these have a load control input, while the other loads a new value on every clock cycle. There are two t...

    1. [20 Pts] You are given the data-path below. Note that there are three registers. Two of these have a load control input, while the other loads a new value on every clock cycle. There are two tri-state drivers that connect the outputs of registers A and Bto a common bus. Finally, there is an ALU that can perform two operations: .Pass Y add X and Y X is always the output of register C, while Y is the value...

  • A three phase induction motor draws a starting current which is five times the full load...

    A three phase induction motor draws a starting current which is five times the full load current with direct on line starting, while developing twice the full load torque. Q2.1. Based on the two facts that starting current is proportional to the applied voltage and that the starting torque is proportional to the square of the applied voltage, determine voltage (as a per cent of rated voltage) required to obtain a starting torque equalling the full load torque. (10 marks)...

  • CODE 102_8 Welding Many welding processes require the application of heat and/or pressure to produce a...

    CODE 102_8 Welding Many welding processes require the application of heat and/or pressure to produce a suitable bond between the two parts being joined. There are a number of conventional and commercially practiced welding processes, which possess limitations in relation to material type and thickness, and in addition, the cost analysis may not allow for a process to be used on a specific application. The selection of suitable welding consumable (electrode or wire) is also an important factor in producing...

  • 15. Calculate the actual rotor speed, in rad/s, at maximum steady-state torque for the machine gi...

    Example 6C: 15. Calculate the actual rotor speed, in rad/s, at maximum steady-state torque for the machine given in Example 6C for operation as a motor when connected to an electric source of (a) 120 Hz with twice rated voltage, (b) 60 Hz with rated voltage, (c) 30 Hz with one-half rated voltage, and (d) 6 Hz with 10 percent rated voltage. Example 6C. The parameters for the equivalent circuit shown in Fig. 6.8-1 may be calculated by using electromagnetie...

  • B oth 100 Day PH262 Page 1 of 5 Lab #13 AC Circuits, Part 1 RC...

    B oth 100 Day PH262 Page 1 of 5 Lab #13 AC Circuits, Part 1 RC & RL, Phase Measurements THEORY The rotating phase representation for series AC circuits should be familiar from textbook and lecture notes A brief outline of the essential points is provided here. If a series RLC circuit is connected across a source of om which is a sinusoidal function of time, then und all its derivatives will also be inside. Sonce all demits in a...

  • The Foundational 15 Please provide equation/formula so i know how to solve for. Some screenshot have...

    The Foundational 15 Please provide equation/formula so i know how to solve for. Some screenshot have answer in it but could be wrong. PLEASE IGNORE ANSWER IN THE PICTURE. Please provide equation/formula so i know how to solve for. Some screenshot have answer in it but could be wrong. PLEASE IGNORE ANSWER IN THE PICTURE. Required information The Foundational 15 [L012-2, L012-3, L012-4, LO12-5, LO12-6] [The following information applies to the questions displayed below.) Cane Company manufactures two products called...

  • QUESTION THREE [25] EC, an engineering company, produces tools and components to customers' specific requirements. EC...

    QUESTION THREE [25] EC, an engineering company, produces tools and components to customers' specific requirements. EC uses absorption costing to absorb overheads into the cost of each customer order. Selling prices are usually determined by adding a 30% mark up to the costs incurred in completing the order. EC has recently been asked to provide a quotation for a new customer. The details of the work have been discussed at a meeting with the customer and the following resource requirements...

  • My Courses Week 2 Assignment(s) Week 2 Assignment(s) Assignment 2 Power Markets have two subcateg...

    My Courses Week 2 Assignment(s) Week 2 Assignment(s) Assignment 2 Power Markets have two subcategories: generation and grid ancillary services (page 113). Text box 2-2a (page 101) describes grid ancillary services and text box 2-2b (page 102) describes essential reliability services. Create a table which lists the grid ancillary services with services as the rows and resources (hydropower, solar, and wind) as columns. In the respective row/column box summarize if the resource can provide the service, with a bottom line...

  • Minutes from the Planning Committee Meeting Present: Ms. Morehouse, administrator; Mr. Hassan, finance and admissions coordinator;...

    Minutes from the Planning Committee Meeting Present: Ms. Morehouse, administrator; Mr. Hassan, finance and admissions coordinator; Mr. Washington, food services director; Ms. Laird, director of nursing; Ms. Smith, rehabilitation supervisor; Mr. Keith, construction representative; Mr. Morgan, designer; Mr. Welbourne, contractor; Ms. Reese, architect. The meeting started at 9 a.m. Ms. Morehouse began with introductions of those present. She 702 explained that culture change in the nursing home industry was going to gain momentum and, if traditional facilities did not adapt...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT