HomeworkLib
Question

composite engineering: "The lamina thickness of a composite [0/90/] plate is 10 mm. Given that the...

composite engineering:

"The lamina thickness of a composite [0/90/] plate is 10 mm. Given that the Young's modulus E for the laminas with O ^ 0 and 90° fiber direction are 45 GPa and 12 GPa, respectively. Find the bending stress o on the bottom and top surface of the plate when the bending moment M = 500 N.m is applied. Also, calculate the bending stiffness of the plate knowing that the width of the plate is 60 mm. Hint: Use transformed section method and lamina with O ^ 0 fiber direction as the reference layer" (The Plate consiste of two layers [0/90].
engineering   Mechanical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

0 0
Add a comment
Know the answer?
Add Answer to:
composite engineering: "The lamina thickness of a composite [0/90/] plate is 10 mm. Given that the...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • M8.16 The transformed-section method scenes 210 mm 28 mm E 160 GPa E=90 GPa 76 mm...

    M8.16 The transformed-section method scenes 210 mm 28 mm E 160 GPa E=90 GPa 76 mm K 240 mm y (mm) A composite beam cross section consists of two rectangular bars securely bonded together. The beam is subjected to a bending moment M = 20 kN-m that produces compression stress at H Determine: Oн (MPa) a) the vertical distance from K to the horizontal centroidal axis Ок (MPa) b) the bending stress produced at H c) the bending stress produced...

  • 3. A [0/90]s graphite/epoxy laminate is subjected to a tensile normal load of 1N/m in the x- dire...

    3. A [0/90]s graphite/epoxy laminate is subjected to a tensile normal load of 1N/m in the x- direction (the direction parallel to the fibers in the 0° ply). Assume the thickness of each ply is 5 mm and use properties of unidirectional graphite/epoxy lamina from the table. a) Calculate the resultant strains of the laminate b) Calculate the global stresses in the laminate c) Calculate the principal stresses (stresses in material directions) of the top layer. Typical Mechanical Properties of...

  • Question 1 (Total 100/3 Marks) Figure 1 (all units are mm) shows a simply supported beam of span ...

    Question 1 (Total 100/3 Marks) Figure 1 (all units are mm) shows a simply supported beam of span 2500 mm with a 5 kN/m load. The cross-section of the beam is a composite section made from two steel plates attached to the top and bottom of a timber section. The top steel plate is 5 mm wide and 20 mm deep. The bottom steel plate is also 5 mm wide but 10 mm deep. The timber section is 50 mm...

  • please solve 2 and 3 1- The reduced stiffness matrix [Q] is given for a unidirectional...

    please solve 2 and 3 1- The reduced stiffness matrix [Q] is given for a unidirectional lamina as follows: 5.681 0.3164 0 ] [Q]=0.3164 1.217 0 Msi I 0 0 0.6006 Calculate the four engineering constants E1, E2, V12, G12 of the lamina. 2- Calculate the transformed reduced stiffness [Q] for the above problem for 0 = 30°. Glass 3- A glass/epoxy lamina consists of 70% fiber volume fraction. Use properties of glass and epoxy from the tables below to...

  • Problem 2 (30 points): Bored at the swimming pool and without enough solid mechanics to occupy their minds over the summer, engineering students analyze a diving board made from a 50mm x 300 mm wood...

    Problem 2 (30 points): Bored at the swimming pool and without enough solid mechanics to occupy their minds over the summer, engineering students analyze a diving board made from a 50mm x 300 mm wood plank. The diving board is held down at end A by anchor bolts that can be considered as a pinned support. a) Draw the Shear and bending moment diagram for the beam (10 points) b) What maximum permissible load, Pmax, can be exerted on the...

  • The rectangular steel plate below measures 1 m x 0.5 m x 10 mm. Assume that...

    The rectangular steel plate below measures 1 m x 0.5 m x 10 mm. Assume that the 1 m dimension is in the x-direction and the 0.5 m dimension is in the y-direction. The plate is made of a material with an elastic modulus of 200 GPa and Poisson's Ratio of 0.3. Suppose a uniform normal stress, Ox, of 125 MPa is applied in the x-direction a) Calculate the stress, ay, required to produce a transverse strain Ey 0 (in...

  • 3. Power transmission is an important engineering application and relies on the integrity of the shaft designs. Assume a solid, circular steel shaft with a uniform diameter d 50 mm and a total le...

    3. Power transmission is an important engineering application and relies on the integrity of the shaft designs. Assume a solid, circular steel shaft with a uniform diameter d 50 mm and a total length I3 m. At its midpoint, a belt passes over a pulley and delivers 50 kW power to the shaft. This power is used to drive two machines at either end of the shaft. Machine 1 consumes P1 20 kW and machine 2 uses P230 KW. The...

  • A wood beam (1) is reinforced on its lower surface by a steel plate (2) as...

    A wood beam (1) is reinforced on its lower surface by a steel plate (2) as shown in the figure. Dimensions of the cross section are b 1 = 220 mm , d = 385 mm , b 2 = 190 mm , and t = 25 mm . The elastic moduli of the wood and steel are E 1 = 12.5 GPa and E 2 = 200 GPa , respectively. The allowable bending stresses of the wood and steel...

  • Macromechanics 215 N, 1000 N/m; all remaining components are equal to zero b) Mry 1 Nm/m; all rem...

    I need help with question 6.18 Macromechanics 215 N, 1000 N/m; all remaining components are equal to zero b) Mry 1 Nm/m; all remaining components are equal to sero ) Comment on the coupling efects obsereed 6.12 Compute the strains ( (y, and ry at the interface between the 459 and laminae above the middle surface by using the results of case (b) of Ezercise 6.11 and -45 /a.e3 6.23). cise 6.13 Compute the stresses ơz and σ1 in the...

  • need solution for milestones A Q1 Solid Mechanics 3 Assessment Task 1a - 2020 Milestone a...

    need solution for milestones A Q1 Solid Mechanics 3 Assessment Task 1a - 2020 Milestone a Question 1. For each of the plane-stress conditions given below, construct a Mohr's circle of stress, find the principal stresses and the orientation of the principal axes relative to the xy axes and determine the stresses on an element, rotated in the x-y plane 60° counterclockwise from its original position: (a) dx = 200 MPa Oy - 300 MPa T .40 MPa (b) dx...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT