What should the length-to-diameter ratio of a face mill cutter with 60-mm diameter preferably be?

Question

Question

engineering Mechanical-Engineering

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

1001on 8f the cutter is perpendicular to the 9. (6 points) A 3-in.-diameter end mill with...

1001on 8f the cutter is perpendicular to the 9. (6 points) A 3-in.-diameter end mill with five teeth is to machine a 1.125 in. width of eut to a square shoulder. A chip load of,006 ipt and a spindle rpm of 600 are initially recommended. Too l fced Rate Tool teed (pm) Spindle rotation (rpm dele Width of cut-1.125 The figure shows Climo milling (choose from "limb and conventional"), The feed rate is ipm.
A Face Milling Operation on machine steel plate is performed with a 2" diameter (D) cutter...

A Face Milling Operation on machine steel plate is performed with a 2" diameter (D) cutter (High Speed Steel) of 6 tecth. Using Cutting speed of steel (CS) and Chip load per tooth (Feed) from lab manual table Length (L): 6 inch Determine Time to cross the plate in seconds (Tm) Spindle 2 inches 6 inches
A 150 mm diameter slab-milling cutter has 10 teeth and is used at a feed speed...

A 150 mm diameter slab-milling cutter has 10 teeth and is used at a feed speed of 1.5 mm/s. estimate the "ideal" arithmetical mean surface roughness when the rotational frequency of the cutter is 3 s1 93

A face milling operation removes 4.0 mm from the top surface of a rectangular piece of...

A face milling operation removes 4.0 mm from the top surface of a rectangular piece of aluminum that is 200 mm long by 60 mm wide by 75 mm thick. The cutter follows a path that is centered over the workpiece. It has four teeth and is 100 mm in diameter. Cutting speed = 2.5 m/s, and chip load = 0.27 mm/tooth. Determine (a) maximum metal removal rate during cutting in mm3/seconds (b) machining time in seconds. Cutter position at...
A conducting wire has a 1.97 mm diameter, a 1.0 m length, and a 60 mohm...

A conducting wire has a 1.97 mm diameter, a 1.0 m length, and a 60 mohm resistance. What is the resistivity of the material? Please explain how the answer is 1.8288*10^-7 ohm m
A test bar 12.8 mm in diameter and 50 mm initial length is loaded elastically with...

A test bar 12.8 mm in diameter and 50 mm initial length is loaded elastically with 16000 kgf and is elongated 0.36 mm. Its diameter is 12.78 mm under load. Calculate, the modulus of elasticity and Poisson’s ratio of the material.

A cylindrical piece of steel has a diameter of 50 mm and a length of 200...

A cylindrical piece of steel has a diameter of 50 mm and a length of 200 mm. Steel has a density of 7200 kg/m3 a) (3 points) Determine the mass of this piece in kg. 1. b) (3 points) If a 10 mm diameter opening is drilled through the entire length of this cylinder and that portion removed, what is the new mass of this piece? c) (4 points) The 10 mm diameter piece is pulled with a force of...
What is the change in side length of a brass rod 3 mm in diameter right...

What is the change in side length of a brass rod 3 mm in diameter right before plastic deformation? The specific brass alloy has a yield strength of 125 MPa, a Young’s modulus of 100 GPa, and a Poisson’s ratio of 0.331.
You have a material of a length of 10mm and a diameter of 0.2 mm. When...

You have a material of a length of 10mm and a diameter of 0.2 mm. When you apply a tensile force of 1.1*104N, this material elongates to the length of 15mm. You measure a diameter of the elongated sample and you find that it is now 0.16 mm. Assuming the deformation remains elastic, calculate Poisson ratio and Young’s modulus of this material (in GPa)

A cylindrical bar of metal having a diameter of 16.5 mm and a length of 183...

A cylindrical bar of metal having a diameter of 16.5 mm and a length of 183 mm is deformed elastically in tension with a force of 42000 N. Given that the elastic modulus and Poisson's ratio of the metal are 67.1 GPa and 0.34, respectively, determine the following:(a) The amount by which this specimen will elongate (in mm) in the direction of the applied stress. (b) The change in diameter of the specimen (in mm). Indicate an increase in diameter...