. Consider an air bubble with radius 0.1 um in water at 20 °C: a. Calculate the overpressure inside the bubble and show your calculation procedures. (The surface tension of water is 72.8 mNm-1) b. Calculate the vapor pressure of water inside the bubble, relative to that over a flat water surface. Show your calculation procedures. (The surface tension of water: 72.8 mN m-1 the molecular weight of water:18 g mol1; the gas constant R: 8.314 J-mol1K-)
. Consider an air bubble with radius 0.1 um in water at 20 °C: a. Calculate...
An air-water vapor mixture enters a heater-humidifier unit at 5°C, 100 kPa, 50% rh. The flow rate of dry air is 0.1 kg/s. Liquid water at 10°C is sprayed into the mixture al the rate of 0.0022 kg/s. The mixture leaves the unit at 30°C, 100 kPa. Calculate (a) the relative humidity at the outlet (b) the rate of heat transfer to the unit
a. Calculate the dry air and water vapor mass flow rates (lb/min) if the volume flow rate is 1,000 cfm, the humidity ratio is 0.025 lbv/lba, and the dry air density is 0.072 Iba/ft3. b. Assume the above air enters an evaporator coil at 90°F where it is cooled in a constant humidity ratio process until reaching the 100 % RH curve ( the temperature at that point is the dew point. The air then keeps dropping in temperature, following...
*Explanations should be brief. Draw a box around each final answer, if applicable.* 1. Consider intermolecular forces and kinetic energies with respect to a solid and a liquid. Explain why molecules in a liquid are free to move past each other, while molecules in a solid are held in fixed positions. 2. Use your knowledge of intermolecular forces to provide an explanation for why the boiling point of 2-hexanol is higher than the boiling point of 2,3-dimethyl-2-butanol. Be sure to...
I need the best solution for these 2 questions on the
section " Check your learning" (10.4 and 10.5) to prepare my exam in class.
Thank you so much for helping me
Y althlon tai sok Translate Gm arch this book O Back Figure 10.20 Depending upon the relative strengths of adhesive and cohesive forces, a liquid may rise (such as water) or fall (such as mercury) in a glass capillary tube. The extent of the rise (or falt is...
Hi,
I need checking on all the work. If anything is wrong then show me
step by step how is done.
11. Obtain a Cu 2 solution of unknown concentration. Write the unknown number on the data sheet. 12. Measure the absorbance of your standard solution, the two dilutions, and the unknown solution. Record these readings on the data sheet. All measurements will be made in the same cuvette and with the instrument set at a wavelength of 630 nanometers...
2ee do heete renouth hecel. to obtein Don't Cs CAS remax let graclolertee C abOu Lecore kmp ris lous knap oin ane vol Barome tris Pressore (u Ha) t8 s Tenpor watC oe AR (me) volome jo.00 mL loo leS. 16 5S.Le 50.6 4.0 le.is 5.80 5.45 caleoltrons Twakr 1/Twak.( Pair (u tnHa Proateam e Peoatatu Calculations: (0.5 pt for each block) Twater (K) 1/Twater (K) Pair (mm Hg) Pwater (mm Hg) Pwater (atm) In Pwater 92 We were unable...
Weight on Earth (lbs.) : 600N or 132lb
Calculate the gravitational force you feel at the
following places. Show your work.
(a)500 km above the surface of Europa.
(b)At the surface of Europa.
(c)Inside the tunnel, half-way through the ocean
layer.
(d)At the bottom of the tunnel.
(e)Evaluate the prediction you made earlier. Did the
gravitational force change as you expected? Explain.
You get back in your space shuttle to continue on your trip. Your next stop is Jupiter you've...
Please answer all the blanks (volume if H2 and
everything in analysis). TIA!
Data 5 1 oong 0.00 10.5ml 2 o.olag 0.00 11.0 Trial 3 o.org 0.00 12.00 o Daag o.albg 0.00 10.0 ml 11.5ml Mass of Mg (g) Initial volume of Syringe (mL) Final volume of Syringe (mL) Volume of H (mL) Barometric pressure (torr) Ambient temperature (°C) Vapor pressure of H2O (torr) 779.314har 23. Oi 21.0 forr TA.314tar 23.0c 179.3 14ton 23.0¢ 779.314 ton 23.0c 779.31472 23.0c 21.0...
10. Write a one-page summary of the attached paper? INTRODUCTION Many problems can develop in activated sludge operation that adversely affect effluent quality with origins in the engineering, hydraulic and microbiological components of the process. The real "heart" of the activated sludge system is the development and maintenance of a mixed microbial culture (activated sludge) that treats wastewater and which can be managed. One definition of a wastewater treatment plant operator is a "bug farmer", one who controls the aeration...