Calculate the amount of work needed to move a proton from the equipotential line of -4V...
1: How much work is done to move a proton from a potential of 5 V to a potential of 20 V... a) In ev? b) In Joules? c) Was the work done by the field, or by an external force? 2: What potential is needed to accelerate a proton to 50,000 m-s? 3: What potential is needed to accelerate an electron to 50,000 m-s'? 4: Given a breakdown voltage for air of 3.0x 10* V-m1, how close would you...
PHYS 1214 General Physics II Exam 2 1: How much work is done to move a proton from a potential of 5 V to a potential of 20 v... a) in ev? b) In Joules? c) Was the work done by the field, or by an external force? 2: What potential is needed to accelerate a proton to 50,000 m-s1? 3: What potential is needed to accelerate an electron to 50,000 m-s1? 4: Given a breakdown voltage for air 013.C...
Work and exact values please! Thank you
Sketch the electric field and equipotential contours for the arrangement shown below. Use the PhET simulation if necessary. Consider the electric field lines drawn below for a configuration or two charges. Five points (A-E) are labeled on the diagram. Rank these locations in order of the electric field strength from smallest to largest. Calculate the net electric potential at point A in the diagram shown above. The net potential is the sum of...
7. What is the amount of energy needed to move an electron through an electrical potential of 3 volts in electronvolts? [3eV] a. W = (V)(a) W= b. in joules? [4.810"}] 8. What is the amount work needed to move 3 electrons through a potential difference of 12 volts a. in electonvolts? [36 eV] W = (v) (a) W= b. in joules? (5.76x10"}]
The lines show the equipotential
contours in the plane of three point charges, Q1, Q2, and Q3. The values of the potentials are in
kV as indicated for the +5, 0, and -5
kV contours. The positions of the charges are
indicated by the dots.
Calculate the external work required to move a negative charge,
q= -8e (where e is, as usual, the charge of a proton) from `a' to
`b' at constant speed.
(Note: The equipotential lines shown are...
please answer questions a-d compeltely and show your work
Part BShow your work on all free-response questions, Be sure to use proper units and significant figures your final answers. For any multiple-choice questions, circle the letter of the one best answer (unless answer is asked for). more than a P P P. P P P 1. Two point charges, Q=-2.5 nC and Q Five equipotential surfaces (dashed curves above) are drawn for you in the diagram. (Assume that V= 0...
If 5 J of work is needed to move a - 0.1 C of charge, then the magnitude of potential difference is " " Volts A uniform electric field, with a magnitude of 500 V/m, is directed parallel to the +x axis. If the potential at x = 5.0 m is 2500 V, what is the potential at x = 2.0 m? A stationary electron is accelerated through a potential difference of 500 V. What is the velocity of the...
How much work (in electron volts) does it take to move a proton from a voltage of 88.8 volts to a voltage of 14.1 volts? Assume 3 significant digits.
How much work must we do on an electron to move it from point A, which is at a potential of +50V, to point B, which is at a potential of -50V, along the semicircular path shown in the figure? Assume the system is isolated from outside forces (e = 1.60 times 10^-19C) 1.60 times 10^-17 J -1.60 times 10^-17 J 1.6 J -1.6 J This cannot be determined because we do not know the distance traveled. If an electron...
How much work is needed to move a 6.8 µC charge from ground to a point whose potential is 50 V?