Question

Find an alternative circuit elements that we can use for the reversed rotational motor. (other than...

Find an alternative circuit elements that we can use for the reversed rotational motor. (other than potentiometer, for controlling motor speed and rotation)

0 0
Add a comment Improve this question Transcribed image text
Answer #1

Instead of going for DC motors, we can also use AC motors.

In the case of DC motors, there are many types. One of the types is a brushless motor where 'Hall effect' phenomenon is used.

Hence, alternative circuit elements can be as follows,

1. Varying voltage

2. Using the method of magnetism

3. Using transistor such that the base current which can vary the circuit output

4. Using the logic circuit

5. a modulator (which will modulate the signal)

Add a comment
Know the answer?
Add Answer to:
Find an alternative circuit elements that we can use for the reversed rotational motor. (other than...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Task 1: Find the effective inertia of the motor and gearbox elements as seen at the...

    Task 1: Find the effective inertia of the motor and gearbox elements as seen at the rotational axis, a. The elements in the drivetrain between the motor and the rotational axis are modelled by the inertias shown in Figure 2. Derive an algebraic expression for the total effective inertia ) as seen at the rotational axis, 8, then substitute the parameter values provided in Table 1. e(t) Jarm NJ1 N1 J1 N2, J2 N3,13 Jencoder Ipotentiometer N5,5 N4,14 Jarmature Itachometer...

  • Computer Control System can anyone solve any of thei questions ? 1 - 10 1. The...

    Computer Control System can anyone solve any of thei questions ? 1 - 10 1. The graph below shows the response of a tachometer. What is the Tach Constant (Kt) of this device in mV/rad per sec? 1000 0 50 100 150 200 250 300 350 400 450 500 Speed Rad/Sec 2. What three parameters of a DC motor must be measured in order to develop the torque-speed curve and the rise time curve for the unloaded motor? 3. What...

  • According to the equivalent circuit of a three-phase induction motor, can we deduce the formulas for...

    According to the equivalent circuit of a three-phase induction motor, can we deduce the formulas for electromagnetic torque calculation? Give your explanation.

  • Consider the circuit below. It is something you might use to approximate the circuit being used...

    Consider the circuit below. It is something you might use to approximate the circuit being used while trying to jump start a car. a) The elements in this drawing represent the dying battery and its internal resistance, the jumper battery and its internal resistance, and the starter motor. (Remember the jumper battery is used to charge the dead battery and power the starter motor.) Identify which parts represent each and explain your reasoning. b) Find the current in the motor...

  • A three-phase, six-pole 440 V, 60 Hz induction motor has the following per-phase equivalent circuit parameters...

    A three-phase, six-pole 440 V, 60 Hz induction motor has the following per-phase equivalent circuit parameters referred to the stator: R1 = negligible, R’2 =0.3 Ω, Rφ = infinite, X1 = 1.131 Ω, X’2 = 1.131 Ω and Xφ = 37.7 Ω. Rotational losses are negligible. Assume the stator is connected to a 440 V, 60 Hz source and use the 6-parameters IEEE model. a) Determine the motor starting torque. (5 points) b) Calculate the motor breakdown torque. (5 points)...

  • A disadvantage of a(n) is that the speed changes when a load is applied to the...

    A disadvantage of a(n) is that the speed changes when a load is applied to the shaft. Electric motor Hydraulic pump Hydraulic motor Electric pump A bi-directional motor circuit uses a 4/3 DCV with a free-float center. Free-wheeling Locking Instant stop O Friction-less A hydraulic brake valve is an adjustable relief valve with pilot lines. Ο TWO Three O Four Five A bi-directional motor circuit with two braking relief valves uses to avoid cavitating the motors. Relief valves O Make-up...

  • A satellite consists two cylinders which can rotate relative to each other about the common axis of summetry. The rotation can be precisely controlled through a built-in motor. Both cyllinders can be...

    A satellite consists two cylinders which can rotate relative to each other about the common axis of summetry. The rotation can be precisely controlled through a built-in motor. Both cyllinders can be asuumed to be uniform; they have the same mass, m = 10.0 kg, and the same radius rc = 0.30m. The top cylinder has attached to it two balls, each of which has mass 1.0 kg and radius rb = 0.1m. Each ball is fastened to the end...

  • how do we calculate ii and iii) - induction motor (25 marks) QUESTION 3 A three-phase,...

    how do we calculate ii and iii) - induction motor (25 marks) QUESTION 3 A three-phase, 400 V, 50 Hz, 4-pole, 1370 rpm, star connected, squirrei-cage induction motor has the following parameters: R, 20, R2- 3 Q, X1-X2- 3.5 and Xm=40 .Motor is controlled by a voltage source inverter at constant V/f ratio. By using IEEE equivalent circuit; Calculate the starting torque and starting current at 10 Hz To- If the torque-speed to be a straight line calculate the slip...

  • Q1/ATV antenna is to be controlled by a 4-phase stepper motor with a step 5 degrees...

    Q1/ATV antenna is to be controlled by a 4-phase stepper motor with a step 5 degrees and reduction gearbox of 1:50. The stepper motor is controlled using Arduino UNO and must scan angular displacement starting from (10) degrees and ending at (170) degrees and repeat, in order to search active working TV-channels. Sketch the controlling cct. and write the computer program that drives the interfacing cct Q2/Say WHY?: 1-Measuring temperature using thermistor needs power supply. 2-7410 and 7404 1Cs can...

  • 2. A string of lights is wired in a series circuit. When one light bulb ns...

    2. A string of lights is wired in a series circuit. When one light bulb ns out, A B the other bulbs will dim. none of the other bulbs will be lit. C D e burnt out bulb becomes a fire hazard. all of the other bulbs will be lit. 2. A string of lights is wired in a series circuit. When one light bulb ns out, A B the other bulbs will dim. none of the other bulbs will...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT