Given the following data from a experiment :
Mass (g) of Dry Empty beaker : 69.3527
Mass (g) of beaker and calcium bicarbonate : 69.5325
-----------------------------------------------------------------
volume (ml) of EDTA used to titrate 10 mL Ca2+ standard Solution :
Trial 1 :18.32
Trial 2: 18.45
Trial 3: 18.35
----------------------------------------------------------------------------------------
Volume (mL) of EDTA used to titrate 20 mL of unknown Ca2+ solution
Trial 1: 25.13
Trial 2: 25.02
Calculate
A) What is the mass (g) of calcium bicarbonate used in the standard?
B) Average volume (mL) of EDTA used to titrate standard ?
C) Molarity (M) of CaCO3 standard ?
D) Molarity (M) of EDTA (Based on average volume)
E) Average volume (mL) OF EDTA for 20 mL of unknown ?
F) Molarity (M) of Ca2+ in unknown?
Please show step by step
Given the following data from a experiment : Mass (g) of Dry Empty beaker : 69.3527...
Molarity of CaCO3 Standard = 0.018 volume (mL) of EDTA used to titrate 10.00 mL Ca2+ standard solution : Trial 1= 17.5, Trial 2= 17.4, Trial 3= 17.4 What is the molarity of (M) of the EDTA (Base on average volume) ? average volume = 17.43
calculations for the % CaO using these numbers from
the experiment are not right. I need help figuring out how to
calculate the percentage
1 Trial 2 l rial Trial 3 Hal (rapp Mass of CaCO mL H20 100.00 standard (g)0.1434 Volume of CaCO3 used (mL) Volume of EDTA used (mL) as.elmLIAk,7| n,し1a8.48mL 3 Conc. EDTA (M) Average Conc. EDTA (M) %Relative Standard Deviation (RSD) Mass of unknown Ca2" (g) Volume of unknown 3 | 9 , 31 100.00 mL...
Please find the
molarity of CaCo3 standard given that the concentration is
179mg/100mL. Then please answer the questions and calculations
below.
EDTA revised procedure (No need to make your own standard solution as stated in the original instructions) Equipment needed 2 x 125 ml E. Flasks, 3x 250ml E. Flasks, 1x500ml E. Flask, 3 watchglasses, 1x10ml Volumetric Pipet, 1 pipet bulb, 1x10 ml graduated cylinder, 1xBuret, 1 wash bottle and 1 slop beaker 600ml NOTE Do not dump any solutions...
A titration was performed to standardize an EDTA solution. a) A 25.00 mL aliquot of a standard solution containing 0.01500 M Ca2+ required 42.87 mL of EDTA to reach the endpoint. The molarity of the EDTA solution is: ________ M b) That same EDTA solution was then used to titrate an unknown hard water sample. A 40.00 mL aliquot of unknown hard water required 34.21 mL of EDTA solution to reach a distinct endpoint. The concentration of Ca2+ ions (assuming...
Question 8 2 pts Consider the following data. mass of empty beaker = 34.981 g mass of beaker and NaOH = 37.095 g What is the molarity of the resulting solution when this amount of sodium hydroxide is dissolved in enough water to make 500 mL of solution. O.121M 0.130 M 0.112M .106M
can someone help with my lab for hard water
determination
Date DATA SHEET: EXPERIMENT 17 Standardization of EDTA Solution A. 8.0003 Concentration of standard Ca2 solution 1. Trial #1 Trial #2 Trial #3 5.00 mlL 25,00 mL Volume of standard Ca2 2. mL 17.00 mL Final buret reading mL mL 3. O00 mL OO0 mL Initial buret reading 4. mL 00 mL Volume of EDTA used 5. mL mL 6 Molarity of EDTA (Show set-up) М as.oomLcax 8.00 10 I...
how would I calculate my results from the first two data the
first data is my results and the second data I have to calculate
each of those with the information that I have on the first 3
trails I really really need help and i just dont understand thank
you.
1 concentration of EDTA solution 2 molar mass of CaCO3 0.0100 M 100.09 g/mol Trail 1 -Trail 2 Trail 3 12 12.01 11.99 5 Unknown analysis Part 1 (pH...
Please show steps for 32 and 33.
Data Table 1: EDTA Titration Volume Trial Initial EDTA Volume (mL) Final EDTA Volume (mL) Total Volume EDTA Used (mL) 1 9 mL 8.6 mL .3mL 2 8.6 6 2.6 mL 3 6 4.2 1.8mL Average Volume of EDTA Used (mL) 1.6mL Data Table 2: Water Hardness Average Volume of EDTA Used (mL) Concentration Ca2+ lons Per Liter of Water (mol/L) Water Hardness (ppm CaCO3) 1.6mL 32 Using the following equation, determine the...
1. Mass of 50 ml beaker labelled “5 g NaCl” 30.2846 g 2. Mass of 50 ml beaker + ~5.00 g NaCl 35.0111 g 3. Volume of distilled water 20.0 mL 4. Mass of 50 mL beaker + ~5.00 g NaCl + water 54.9981 g 5. Volume of “5 g NaCl” solution 22.2 mL 1. Exact mass of NaCl in beaker labelled “5 g NaC1” 2. Exact mass of solution in beaker labelled “5 g NaCl” g 3. Density of...
Calculations of hardness as CaCO3 in ppm and the Standard
deviation and % Relative deviation. I need help step by step on how
to calculate these.
Trial 1 50.00 33.52 Trial 2 Trial 3 50.00 31.92 Trial 4 Volume of water sample used (mL) Volume of EDTA titrant used (mL) Average Conc. of 50.00 32.47 EDTA (M)4 x10 Hardness as CaCOs (ppm) Average Hardness as CaCOs (ppm) Standard Deviation %Relative Standard Deviation 95% Cl
Trial 1 50.00 33.52 Trial 2...