What does "variable modulus is high" stand for in carbon fiber?

Question

Question

engineering Mechanical-Engineering

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

Describe the differences in mechanical properties between: high modulus, carbon fiber resin composites, 6061-T6 aluminum, Ti...

Describe the differences in mechanical properties between: high modulus, carbon fiber resin composites, 6061-T6 aluminum, Ti 6Al 4V Titanium alloys and 4130 Chromoly Steel
For a continuous carbon fiber Em=3 GPa and Ef=300 GPa, find the minimum volume fraction of...

For a continuous carbon fiber Em=3 GPa and Ef=300 GPa, find the minimum volume fraction of fiber needed to achieve a composite modulus equal to that of titanium, 225 GPa. What would be the transverse modulus?
H based carbon fiber containing a known amount of single walled 5. Consider a pitc Sartbon nanotu...

h based carbon fiber containing a known amount of single walled 5. Consider a pitc Sartbon nanotubes (SWNT), By adding small amounts of single walled carbon nanotubes SWNT) to the pitch prior to fiber pulling, the elastic fibers can be i the following questions a. (10 points) Estimate the elastic modulus for both the 1% and 5% SWNT loaded carbon fibers. modulus of the pitch based carbon ncreased. Use the figure below and the other information (given) to answer 700...

In an aligned and continuous carbon fiber-reinforced nylon 6,6 composite, the fibers are to carry 94...

In an aligned and continuous carbon fiber-reinforced nylon 6,6 composite, the fibers are to carry 94 % of a load applied in the longitudinal direction. Modulus of Elasticity [GPa(psi)] Tensile Strength [MPa(psi)] Carbon fiber 260 (37 ×106) 4000 (5.8 ×105) Nylon 6,6 2.8 (4.0 ×105) 76 (11,000) (a) Using the data provided, determine the volume fraction of fibers that will be required. (b) What will be the tensile strength of this composite? Assume that the matrix stress at fiber failure...
Q1) For a unidirectional carbon fiber reinforced lamina composites, fiber volume fraction 0.65, En-300 GPa, En...

Q1) For a unidirectional carbon fiber reinforced lamina composites, fiber volume fraction 0.65, En-300 GPa, En = 30 G Pa, Gn2-40 G Pa while for matrix, Gm-10 GPa, Em-3 GPa Determine the longitudinal and transverse moduli of the composites, and the shear modulus of the composites.
A unidirectional glass fiber-epoxy matrix composite containing 65 vol% fiber, calculate the modulus of elasticity in...

A unidirectional glass fiber-epoxy matrix composite containing 65 vol% fiber, calculate the modulus of elasticity in the longitudinal direction and the transverse direction. Epoxy has a density of 1.54 g/cm3, modulus of elasticity of 3.5 GPa, yield strength of 60 MPa, tensile strength of 95 MPa, and Poisson’s ratio of 0.33. Glass fiber has a Poisson’s ratio of 0.22.

51. About how much lower in density is carbon fiber composite versus steel? A. Carbon fiber...

51. About how much lower in density is carbon fiber composite versus steel? A. Carbon fiber is about 2X heavier B. Carbon fiber is about 2X lighter C. Carbon fiber is about 5X lighter D. Carbon fiber is about 50X lighter
For the following fiber and matrix material properties Fiber (F) Matrix 1 (M1)Matrix2 (M2) Elastic Modulus...

For the following fiber and matrix material properties Fiber (F) Matrix 1 (M1)Matrix2 (M2) Elastic Modulus Shear Modulus Poisson's Ratio Densitv 85 GPa 35 GPa 0.20 2500 kg/m 3.5 GPa 1.5 GPa 0.30 35 GPa 15 GPa 0.30 1200 kg/m3 1800 kg/m Use following fiber volume ratio values with 0.05 increment. Vf - (0,0.05, 0. 10, 0.15, 0.20, 0.25,..,1) 1. (25 pts.) Determine the fiber to composite load ratio (F/ ) vs. fiber volume ratio Vf) curves for F-M1 and...
When using the formula Y= A+Bx what does the A and the X stand for: variable...

When using the formula Y= A+Bx what does the A and the X stand for: variable cost per unit or fixed costs or relevant range? True or False: Labor material and overhead are called manufacturing costs True or False: Guards at the office building are classified as an administrative cost.

An E-glass fiber-thermoset polyester composite tube is carefully constructed with the objective o...

An E-glass fiber-thermoset polyester composite tube is carefully constructed with the objective of achieving maximum axial tensile modulus. The glass fibers are continuous and highly aligned parallel to the tube axis. The tube contains 70% by volume glass, and has dimensions: length lm, diameter 50 mm, and wall thickness Predict the following deformations: a) The changes in length and diameter when the tube carries an axial tensile load of 10kN. The change in diameter when the tube is internally pressurized...