Plus minus tolerances and geometric tolerances cannot be used together on the same view of a...
Plus minus tolerances and geometric tolerances cannot be used together on the same view of a print.
True or False
Homework Answers
Answer - True
All dimensions must have a tolerance. Every feature on every manufactured part is subject to variation, therefore, the limits of allowable variation must be specified. Plus and minus tolerances may be applied directly to dimensions or applied from a general tolerance block or general note. For basic dimensions, geometric tolerances are indirectly applied in a related Feature Control Frame. The only exceptions are for dimensions marked as minimum, maximum, stock or reference.
Add Answer to:
Plus minus tolerances and geometric tolerances cannot be used
together on the same view of a...
Fill in the blank and/or circle the following Orientation geometric tolerances control ______, ________, and __________...
Fill in the blank and/or circle the following Orientation geometric tolerances control ______, ________, and __________ _________ tolerances control the relationship of features to one another. Which of the followin does orientation tolerance imply: MMC, RFS, or LMC Define parallelism. _______________________ Parallelism can be applied to the axes of two or more features when a parallel relationship between the features is desired. True or False?
1. Phantom lines are used to "shade" the area of material cut by the cutting plane....
1. Phantom lines are used to "shade" the area of material cut by the cutting plane. true or false. a) True b) False 2. A revolved section has a cutting plane slicing through a feature, but the section view itself is "rotated" 90 degrees directly on the regular view. true or false. a) True b) False 3. Using the plus and minus dimensioning method, tolerances are given as a basic dimension with a unilateral tolerance in one direction or with...
Add geometric tolerances to the drawing based on the requirements listed below. 121.125 1. The front...
Add geometric tolerances to the drawing based on the requirements listed below. 121.125 1. The front surface (front view face) is Datum Feature A. 2. The center hole axis is Datum Feature B. 3. The slot center-plane is Datum Feature 4. The axis of the center hole is perpendicular to Datum A to within 1 mm at MMC. 5. The position tolerance of the slot is 2 mm at MMC w.r.t. primary Datum A, then secondary Datum Bat MMB. 6....
17. explain the strategy used by a plus-sense RNA virus, minus-sense RNA virus, DNA virus and...
17. explain the strategy used by a plus-sense RNA virus, minus-sense RNA virus, DNA virus and retrovirus to get each of their genomes copied during replication [Hint: see the table if you cannot remember] 18. explain the strategy used by each of the following viruses to get host cells to make their proteins for them: double-stranded DNA, plus-sense RNA, minus-sense RNA, retroviruses [Hint: see the table if you cannot remember]
A 95% confidence interval for µ is 15 plus-or-minus 3. This confidence interval is used to...
A 95% confidence interval for µ is 15 plus-or-minus 3. This confidence interval is used to test the null hypothesis LaTeX: H_0\:\mu=10H 0 μ = 10
A certain university has decided to introduce the use of plus and minus with letter grades,...
A certain university has decided to introduce the use of plus and minus with letter grades, as long as there is evidence that more than 40% of the faculty favor the change. A random sample of faculty will be selected, and the resulting data will be used to test the relevant hypotheses. If π represents the true proportion of all faculty that favor a change to plus-minus grading, which of the following pair of hypotheses should the administration test: a)...
Scantron - Multiple Choice True/False General knowledge from lab section of course Practice Problems 1. 2. 3. 4. A section view cannot replace one of the three standard orthographic views when used i...
Scantron - Multiple Choice True/False General knowledge from lab section of course Practice Problems 1. 2. 3. 4. A section view cannot replace one of the three standard orthographic views when used in a drawing When considering geometric tolerance, the Nominal Size and the Basic Size are never the same value An interference fit guarantees that there will be space or "wiggle room" between the two mating parts It is acceptable to dimension to hidden lines A part has a...
The output function printf() cannot be used in C++ programs.
The output function printf() cannot be used in C++ programs. True False
Information is considered to be processed data plus the applications that are used in the processing...
Information is considered to be processed data plus the applications that are used in the processing of the data. True False When implementing solutions to enable the A in CAIN, encryption is almost always a part of the solution. True False A strategy of defense in depth is the proper solution to securing cloud based information systems. True False
A sharing arrangement in a “cost plus incentive fee arrangement” should be the same on either...
A sharing arrangement in a “cost plus incentive fee arrangement” should be the same on either side of the target cost (same % sharing to buyer and seller). Question 27 options: True False
Add geometric tolerances to the drawing based on the requirements listed below. 121.125 1. The front surface (front view face) is Datum Feature A. 2. The center hole axis is Datum Feature B. 3. The slot center-plane is Datum Feature 4. The axis of the center hole is perpendicular to Datum A to within 1 mm at MMC. 5. The position tolerance of the slot is 2 mm at MMC w.r.t. primary Datum A, then secondary Datum Bat MMB. 6....
Scantron - Multiple Choice True/False General knowledge from lab section of course Practice Problems 1. 2. 3. 4. A section view cannot replace one of the three standard orthographic views when used in a drawing When considering geometric tolerance, the Nominal Size and the Basic Size are never the same value An interference fit guarantees that there will be space or "wiggle room" between the two mating parts It is acceptable to dimension to hidden lines A part has a...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago