Many birds can attain very high speeds when diving. The mass of a diving swallow is estimated to be 0.018 kg, its drag coefficient is 0.12, and its cross-section area as 5.6×10−4m2.
What is the terminal velocity for this swallow as it dives?
Many birds can attain very high speeds when diving. The mass of a diving swallow is...
At very low speeds, the resistance to motion offered by a liquid or gas is nearly proportional to velocity; such a viscous drag force opposes the motion and can be writ- ten fviscous = −bv, where the constant of proportionality is known as the viscous drag coefficient. A tiny spherical metal particle of mass 6 × 10−6 g (neglect buoyancy ef- fects) falling though oil has a drag coefficient b = 3 × 105 kg/s. What is its terminal speed?
An object with cross section A is shot horizontally across frictionless ice. Its initial velocity is v0x at t0=0s. Air resistance is not negligible. A 1.8 m wide, 1.5 m high, 1700 kg car with a drag coefficient of 0.35 hits a very slick patch of ice while going 24 m/s . Air resistance is not negligible. If friction is neglected, how long will it take until the car's speed drops to 11 m/s ? To 5.0 m/s ?
1. A rocket is launched vertically from the Earth, and the thrust (pushing force) from the engines is directed upward, and has a magnitude of 5.00 x 106 N. The mass of the rocket is initially 2.00 x 105 kg. (a) What is the initial acceleration of the rocket, assuming you can neglect air resistance? (b) After the rocket has been in flight for a while, burning and exhausting a lot of fuel, its mass has decreased to 1.20 x 105 kg, and...
A 505-g squirrel with a surface area of 920 cm2 falls from a 4.4-m tree to the ground. Estimate its terminal velocity. (Use therag coefficient for a horizontal skydiver. Assume that the cross-sectional area of the squirrel can be approximated as a rectangle of width 11.5 cm and length 23 cm. Note, the squirrel may not reach terminal velocity by the time it hits the ground. Give the squirrel's terminal velocity, not it's velocity as it hits the ground.) ITn/s...
Please don't attempt if you can not write a MATLAB
PROGRAM.
I don't need numerical physics solution, I need MATLAB code.
Read the question carefully
2) Falling Drops Imagine a solid sphere of diameter, d, falling through the air. After its release, the sphere accelerates until it reaches its terminal velocity. The terminal velocity is obtained when the drag force due to air friction, Fa, balances the weight of the sphere, W. The weight of the sphere is simply its...
A
11-2 A rock with a diameter of 20 cm is dropped from a very high cliff. Using the 01pts drag-force equation F-(0.25) density of airXcross-sectional area)v2, estimate the time it will take for the rock to reach terminal velocity. The density of air is about 1.2 kg/m3. Submission History Incorrect. Your answer: "5 min". Score: 0/0.1 You may resubmit below: OA. 30s 5 min C. 30 min OD. 2 hours ов. 11-3 A wrench of mass 1.5 kg is...
explain please
E. arctan(a/vr) 11. In what aituations, if ang, can force? body move in a eircular peth at coatant ped withoal eeatripetal A. None. 0) In certain special non-inertial frames C. In all non-inertial frames. ex, D. In all inertial frames. E Always 12. A loaded penguin sled weighing 80 N reeta on a plane inclined at angle 20 to the horieontal (ee Egure below) Between the sled and the plane, the coefficieet of static friction in 0.25, and...
Could you please answer these questions
1-
++++++++
2-
+++++++
3-
+++++++
4-
++++++++++++++
5-
++++++++++
6-
+++++++++
7-
+++++++
8-
++++++++++++++
9-
Calculate the average density of the following astronomical body: Mars. Mars = kg/m3 Where does the value fit among those listed in the table below? Look up the density of a typical rock, such as granite in another source and compare the density of Mars to it. A proton, which is the nucleus of a hydrogen atom,...
summarizr the followung info and write them in your own words and break them into different key points. 6.5 Metering Chamber: 6.5.1 The minimum size of the metering box is governed by the metering area required to obtain a representative test area for the specimen (see 7.2) and for maintenance of reasonable test accuracy. For example, for specimens incorporating air spaces or stud spaces, the metering area shall span an integral number of spaces (see 5.5). The depth of...
summatize the following info and break them into differeng key points. write them in yojr own words
apartus
6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...