A solar collector consists of a flat plate that absorbs the heat of sunlight. A water...
A solar collector consists of a flat plate that absorbs the heat
of sunlight. A water pipe attached to the back of the plate carries
away the absorbed heat. Assume that the solar collector has an area
of 4.9 m2 facing the Sun and that the power
per unit area delivered by sunlight is 1000 W/m2.
What is the rate at which water must circulate through the pipe if
the temperature of the water is to increase by 31 C as it passes
through the detector?
Homework Answers
total power received by solar collector is
P = 1000 x 4.9 = 4900 W
the specific heat capacity of water is 4186 J/kg/C
The rate at which water must circulate through the pipe if the temperature of the water is to increase by 31 C is
Add Answer to:
A solar collector consists of a flat plate that absorbs the heat
of sunlight. A water...
Q2. Solar flat plate water heater is shown below. Solar collector Controller Hot water to the...
Q2. Solar flat plate water heater is shown below. Solar collector Controller Hot water to the tap Tank t Cold water food Pump (a) What is the principle on which the solar collector works? Explain. (1.5 marks) (b) What is the principle on which the heat exchanger works? Explain. (1.5 marks) Q3.(a) The wavelength of radio waves is 200 m & its speed iſs 3x108m/s in free space. (1) Find the frequency of the radio waves in space? (1.5 marks)...
A flat plate collector mounted on plane surface operates with efficiency of 40% it installed at a...
A flat plate collector mounted on plane surface operates with efficiency of 40% it installed at a location 45◦ N, the time is 10:00 am, April 1, 2019. When the collector faces the sun directly it delivers 870 W to the water, how much power will deliver if the surface is set at an elevation of 25◦ and facing east? You can assume that the conversion efficiency from solar power to power absorbed by the fluid remains constant, what changes...
A flat-plate solar collector is used to heat atmospheric air flowing through a rectangular channel. The...
A flat-plate solar collector is used to heat atmospheric air flowing through a rectangular channel. The bottom surface of the channel is well insulated, while the top surface is subjected to a uniform heat flux 96,which is due to the net effect of solar radiation absorption and heat exchange between the absorber and cover plates. W Transparent cover plate Absorber plate Rectangular channel Air Tmi, m Beginning with an appropriate differential control volume, obtain an equation that could be used...
An unglazed flat plate solar water heater is orientated perpendicular to the sun such that the in...
An unglazed flat plate solar water heater is orientated perpendicular to the sun such that the incident radiation reaching the plate is 1100 W/m2. The plate has a semi selective coating such that the plate absorptivity and emissivity is equal to unity for all wavelengths up to 2µm, and 0.13 for all λ > 2µm. Coolant flowing in the collector tubes removes heat at such a rate as to maintain the plate temperature at 80°C. Considering the sun to be...
Determine the overall heat transfer coefficient (UL) for a Flat Plate Solar Collector inclined at 45...
Determine the overall heat transfer coefficient (UL) for a Flat Plate Solar Collector inclined at 45 degrees to the horizontal and facing south. The average ambient temperature for the day is 20 degrees C and the observed glass and absorber plate temperatures are 45 degrees C and 69 degrees C respectively. The system is provided with 6 cm thick insulation (glass wool, k = 0.04 W/m degrees C) at the bottom. The air space between the absorber plate and glass...
In a solar water heater, energy from the Sun is gathered by water that circulates through...
In a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector. The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 29.0% (that is, 71% of the incident solar energy is lost from the system). What collector area is necessary to raise the temperature of 430...
In a solar water heater, energy from the Sun is gathered by water that circulates through...
In a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector. The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 28.0% (that is, 72% of the incident solar energy is lost from the system). What collector area is necessary to raise the temperature of 240...
In a solar water heater, energy from the Sun is gathered by water that circulates through...
In a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector. The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 29.0% (that is, 71% of the incident solar energy is lost from the system). What collector area is necessary to raise the temperature of 350...
Problem 3: The specifications of a flat-plate collector is as follows: τ = 0.88, α 0.97, U = 1.3 Btu/h ft2 °F. The heat removal factor for the collector is 0.92, the solar insolation is 210 Btu/h ft2...
Problem 3: The specifications of a flat-plate collector is as follows: τ = 0.88, α 0.97, U = 1.3 Btu/h ft2 °F. The heat removal factor for the collector is 0.92, the solar insolation is 210 Btu/h ft2, and the ambient air temperature is 60°F. Determine (a) the collector efficiency if the water enters the collector at 115°F and (b) the temperature of water at which the collector efficiency is zero. Take the incident angle modifier to be 1
Problem...
Chapter 18, Problem 029 In a solar water heater, energy from the Sun is gathered by...
Chapter 18, Problem 029 In a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector. The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 14.0% (that is, 86% of the incident solar energy is lost from the system). What collector area is necessary to raise...
Q2. Solar flat plate water heater is shown below. Solar collector Controller Hot water to the tap Tank t Cold water food Pump (a) What is the principle on which the solar collector works? Explain. (1.5 marks) (b) What is the principle on which the heat exchanger works? Explain. (1.5 marks) Q3.(a) The wavelength of radio waves is 200 m & its speed iſs 3x108m/s in free space. (1) Find the frequency of the radio waves in space? (1.5 marks)...
A flat-plate solar collector is used to heat atmospheric air flowing through a rectangular channel. The bottom surface of the channel is well insulated, while the top surface is subjected to a uniform heat flux 96,which is due to the net effect of solar radiation absorption and heat exchange between the absorber and cover plates. W Transparent cover plate Absorber plate Rectangular channel Air Tmi, m Beginning with an appropriate differential control volume, obtain an equation that could be used...
Problem 3: The specifications of a flat-plate collector is as follows: τ = 0.88, α 0.97, U = 1.3 Btu/h ft2 °F. The heat removal factor for the collector is 0.92, the solar insolation is 210 Btu/h ft2, and the ambient air temperature is 60°F. Determine (a) the collector efficiency if the water enters the collector at 115°F and (b) the temperature of water at which the collector efficiency is zero. Take the incident angle modifier to be 1
Problem...
Chapter 18, Problem 029 In a solar water heater, energy from the Sun is gathered by water that circulates through tubes in a rooftop collector. The solar radiation enters the collector through a transparent cover and warms the water in the tubes; this water is pumped into a holding tank. Assume that the efficiency of the overall system is 14.0% (that is, 86% of the incident solar energy is lost from the system). What collector area is necessary to raise...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 11 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 11 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 11 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 11 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 11 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 11 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 11 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 11 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 11 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 11 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 11 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 11 months ago