An AC waveform has an RMS voltage of 60 VAC. What's the waveform's peak voltage?

Question

Question

science physics

Answer 1

✔ Recommended Answer

Answer #1

Peak Voltage is given by:

V_Peak = V_rms*sqrt (2)

V_rms = root mean square voltage = 60 V

So,

V_Peak = 60*sqrt 2

V_Peak = 84.85 V

Please Upvote.

Add a comment

Answer 2

Similar Homework Help Questions

In a sinusoidal AC circuit with rms voltage V, the peak-to-peak voltage equals

In a sinusoidal AC circuit with rms voltage V, the peak-to-peak voltage equals
In an ac series RC circuit, if 20 VAC is measured across the resistor and 40...

In an ac series RC circuit, if 20 VAC is measured across the resistor and 40 VAC is measured across the capacitor, the magnitude of the applied voltage is which of the following? (a) ≈ 60 VAC (b) ≈ 55 VAC (c) ≈ 50 VAC (d) ≈ 45 VAC Draw a circuit diagram and show your calculations Hint: “VAC” is a common unit that means “ac voltage” and it is implied that the voltage is a sine wave. For this...
An AC sine wave has an RMS value of 100 V. What's the average of the...

An AC sine wave has an RMS value of 100 V. What's the average of the waveform?

An AC sine wave voltage has a peak amplitude of 170 V. What is the rms...

An AC sine wave voltage has a peak amplitude of 170 V. What is the rms value?
In order to obtain the peak voltage from an AC source, one multiplies the RMS voltage...

In order to obtain the peak voltage from an AC source, one multiplies the RMS voltage by SQRT(3) 2 RMS^2 SQRT(2)
Find the following for an input of 120 VAC(RMS), 60 hertz, given a 20:1 stepdown transformer....

Find the following for an input of 120 VAC(RMS), 60 hertz, given a 20:1 stepdown transformer. The secondary is less voltage than the primary. Rload is 100 ohms. Round off to the nearest tenths place. 1a: Primary or input peak voltage = 1b: Secondary peak voltage = 1c: Primary peak current =

An ac generator supplies an rms (not peak) voltage of 25 V at 100.0 Hz. The...

An ac generator supplies an rms (not peak) voltage of 25 V at 100.0 Hz. The generator is connected to a circuit whose capacitance is 1.50 μF. What is the rms current of the circuit?
An ac generator supplies a peak (not rms) voltage of 120.0 Volts at 60.0 Hz. It...

An ac generator supplies a peak (not rms) voltage of 120.0 Volts at 60.0 Hz. It is connected in series with a 50.0-Ohm resistor and a 0.500-H inductor. What is the rms current through the resistor (in Amperes)?
QUESTION 1 An AC voltage has a peak value of 2 V. What is the RMS value? (3 decimal places) QUEST...

QUESTION 1 An AC voltage has a peak value of 2 V. What is the RMS value? (3 decimal places) QUESTION 2 A 2 Vp-p voltage is applied to a circuit that has three 1 kohm resistors in series. What is the total current (It) in rms milli amps QUESTION 3 A resistive circuit has three 100 ohm resistors in parallel. A 120 Vrms voltage is applied to the parallel circuit. What is the peak current through one resistor in...

An ac generator supplies an rms (not peak) voltage of 180 V at 60.0 Hz. The...

An ac generator supplies an rms (not peak) voltage of 180 V at 60.0 Hz. The generator is connected in series with a 0.50-H inductor, a 6.0-1F capacitor, and a 300-ohm resistor. What is the peak (not rms) current through the resistor? Vrms=2 Ime (R? +(X2 – Xc)”), Xı = 26 fL, X. : 9 2fC