What is the minimum bandwidth AM signal that can betransmitted and still convey all the necessary...

Question

Question

What is the minimum bandwidth AM signal that can betransmitted and still convey all the necessary intelligence

engineering Electrical-Engineering

Answer 1

Answer #1

In Amplitude Modulation, upper frequency is often limited too 5kHz.

So, minimum bandwidth beacoms 10KHz.

So, AM signals should be at least 10KHz apart to transmit necessary information.

Answer 2

Similar Homework Help Questions

What is the bandwidth of an AM signal whose carrier is 2.1 MHz modulated by a...

What is the bandwidth of an AM signal whose carrier is 2.1 MHz modulated by a 1.5-kHz square wave with significant harmonics up to the fifth? Calculate all the upper and lower sidebands produced.
For a lowpass signal with a bandwidth of 6000 Hz, what is the minimum sampling frequency...

For a lowpass signal with a bandwidth of 6000 Hz, what is the minimum sampling frequency for perfect reconstruction of the signal? What is the minimum required sampling frequency if a guard band of 2000 Hz is required? What is the minimum required sampling frequency and the value of K for perfect reconstruction if the nstruction filter has the following frequency response lfl 7000 K-Kino 7000, 0, H(f) = 7000 < lfl < 10000) otherwise
3.8. (a) What is the theoretical minimum system bandwidth needed for a 10-Mbits/s signal using 16-level...

3.8. (a) What is the theoretical minimum system bandwidth needed for a 10-Mbits/s signal using 16-level PAM without ISI? (b) How large can the filter roll-off factor be if the allowable system bandwidth is 1.375 MHz?

2. (a) (5 points) Determine the minimum cable bandwidth needed to transmit a PCM signal of...

2. (a) (5 points) Determine the minimum cable bandwidth needed to transmit a PCM signal of bandwidth 200 Hz. The maximum acceptable error in sample amplitudes is 0.25% of the peak signal amplitude. The sampling rate must be at least the Nyquist rate. Solution:
A complex bandpass signal has a bandwidth range from 100 kHz to 250 kHz. What is...

A complex bandpass signal has a bandwidth range from 100 kHz to 250 kHz. What is the minimum sampling rate for this signal (in kHz)?
What information does the chemical shift of an NMR signal convey? Select the correct answer. What...

What information does the chemical shift of an NMR signal convey? Select the correct answer. What information does the chemical shift of an NMR signal convey? Select the correct answer. the number of chemically equivalent nuclei that produce the signal the chemical environment near the nuclei that produce the signal the relative mass of the nuclei that produce the signal the stretching frequencies of the bonds adjacent to those nuclei

Consider the following Amplitude Modulation (AM) signal given by

Consider the following Amplitude Modulation (AM) signal given by Xc(t)=Ac[1 + μx(t)]cos(wct) where x(t) is the message signal, and μ the modulation index. Also consider the following message signal x(t) for parts (a) and (b)' shown in Fig 1. a) Provide a sketch of the AM signal when the modulation index μ < 1. b) Provide a sketch of the AM signal when the modulation index μ = 1. c) Provide a sketch of the AM signal when the modulation index μ > 1. d) If the bandwidth...
10 pts Question 3 A signal has a single-sided bandwidth of W - 90 kHz. If...

10 pts Question 3 A signal has a single-sided bandwidth of W - 90 kHz. If this signal is sampled at the Nyquist rate ( fs - 2W samples/sec) and PAM encoded what is the minimum required bandwidth needed for a channel to transmit this signal?
2. For a lowpass signal with a bandwidth of 4000 Hz, what is the maximum sampling...

2. For a lowpass signal with a bandwidth of 4000 Hz, what is the maximum sampling frequency for perfect of a the signal? What is the minimum required sampling frequency if a guardband of 500 Hz is required ? If the reconstruction lter has the frequency response (a) What is the minimum required sampling frequency and the value of K for perfect reconstruction ? h of 4000 Hz, what is the maximum sampling for perfect of a the signal? What...

Problem 3) Design a Double-Side-Band (DSB) based transmitter and receiver (find minimum bandwidth requirement and draw the block diagrams) to send and fully recover 10 human-voice type signals wi...

Problem 3) Design a Double-Side-Band (DSB) based transmitter and receiver (find minimum bandwidth requirement and draw the block diagrams) to send and fully recover 10 human-voice type signals with each signal having the bandwidth of 5kHz. Note that the receiver needs at least 3kHz of separation between each DSB signal for full recovery and you are limited to use AM radio frequency spectrum of 540 to 1600 kHz. Problem 3) Design a Double-Side-Band (DSB) based transmitter and receiver (find minimum...