PROBLEM A rigid tank with a volume of 2.4 m3 contains a moist air mixture having...
11-35.A moist air mixture with a dry bulb temperature of 48°C, a relative humidity of 40 percent, and a total pressure of 160 kPa is contained in a rigid vessel having a volume of 1.65 m3. The air is cooled until the dry bulb temperature reaches 23°C. Determine the amount of heat transferred, the final pressure of the air, and the amount of water vapor condensed during the process.
Exercise 2 Moist air at 1 atm. barometric pressure has a dry bulb temperature of 40°C and a wet bulb temperature of 320C. Using both the equations for the moist air properties and the psychrometric chart find: g) the partial pressure of the water vapor h) humidity ratio i) relative humidity j) dew-point temperature k) specific volume 1) enthalpy of moist air Insert the data and the results from the chart in the following table: Enthalpy Specific kJ/kg m/kg Humidity...
Question 3 A rigid tank, of 0.5 m volume, contains an ideal-gas mixture at 300 K. The mixture is made up of 2.4 kg of gas A and 1.4 kg of gas B, the molecular weights of which are MA = 32.0 kg/kmole and M 28.0 kg/kmole, respectively. i. Determine the mass fraction of A and B. (3 marks] ii. Determine the mole fraction of A and B. [5 marks] iii. Determine the molecular weight of the mixture. [2 marks]...
Exercise 3 Moist air at 1 atm. barometric pressure has a dry bulb temperature of 29 C and a wet bulb temperature of 22°C. Using the psychrometric chart and the table for saturated vapor find the following air properties: Pr T- 40 a) the partial pressure of the water vapor b) humidity ratio c) relative humidity d) dew-point temperature e) specific volume ) enthalpy of moist air
A rigid tank having a volume of 0.1 m3 initially contains water as a two-phase liquid-vapor mixture at 1 bar and a quality of 1%. The water is heated in two stages: Stage 1: Constant-volume heating until the pressure is 20 bar. (treat as closed system) Stage 2: Continued heating while saturated water vapor is slowly withdrawn from the tank at a constant pressure of 20 bar. (Note: Use transient analysis with all the water leaving having a quality of...
Pressure in tank = 2320 kPaQuality of saturated mixture = 0.0269A 9.8 m3 rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. Determine the density of the mixture. (Round the final answer to one decimal place.) (You must provide an answer before moving on to the next part.) The saturated water-temperature table (in Sl units) is given below.The density of the mixture is _______ kg/m3
A rigid tank with a volume of 0.117 m3 contains 1 kg of R134a vapor at 240 kPa. Determine the initial pressure and final temperature.
An air conditioner operating at steady state takes in moist air at 28ºC, 1 atm and 70% relative humidity. The moist air first passes over a cooling coil in the dehumidifier unit and some water vapor is condensed. The rate of heat transfer between the moist air and the cooling coil is 38.69 kW. Both saturated moist air and condensate streams exit the dehumidifier unit at the same temperature. The moist air then passes through a heating unit, exiting at...
A rigid tank that contains 2.4 kg of N2 at 25°C and 550 kPa is connected to another rigid tank that contains 4.4 kg of O2 at 25°C and 150 kPa. The valve connecting the two tanks is opened, and the two gases are allowed to mix. If the final mixture temperature is 25°C, determine the volume of each tank and the final mixture pressure. The gas constants of N2 and O2 are 0.2968 and 0.2598 kPa.m3/kg.K, respectively. The universal...
NEED HELP
A rigid, poorly insulated tank with a volume of V1.0 m3 initially contains a saturated water vapor (quality of 1.0) at a pressure of 3 bars (300 kPa). The tank is connected to a supply line valve is opened and 2.0 kg of steam enters the rigid tank, after which the valve is closed. The pressure is measured after the valve is closed and it is found that p2-5 bars (500 kPa). Find (a) the state of the...