
PLEASE SHOW WORK 5 points A 39,3 resistor is connected to the secondary of an ideal...
An ideal transformer with 5 turns on the primary and 10 turns on the secondary is shown in the figure. A sinusoidal voltage source having V(t) = 10 sin(100t) volts is connected across the primary and a 1 Ω resistor is connected across the secondary. What is the maximum value of the current in the primary circuit (not the secondary)? (answer is 40 amps)
An ideal transformer has 4500. turns in its primary (input) and 14500. turns in its secondary (output). 10.0-V ac is connected to the primary (input). a) What is the voltage on the secondary (output)? b) What is the secondary (output) current if an 8.00-Ω resistor is connected to the secondary (output)? c) What is the power supplied to the primary (input)?
An ideal transformer has 4500. turns in its primary (input) and 14500. turns in its secondary (output). 10.0-V ac is connected to the primary (input). a) What is the voltage on the secondary (output)? b) What is the secondary (output) current if an 8.00-Ω resistor is connected to the secondary (output)? c) What is the power supplied to the primary (input)?
show all work 1. a transformer is connected to a 460 VAC line. The secondary voltage is 230VAC. The load connected to the secondary voltage draws 30A. a. what is the turns ratio of the transformer? b. How much current flows in the primary circuit? 2. You find that under unusually heavy loads, the voltage in your plant drops to 456 V. What will be the resulting secondary voltage if you use a transformer with a 4:1 primary to secondary...
PLEASE SO PART C, THANK YOU WILL RATE.
A single-phase transformer with a 5:1 turns ratio is connected to a 600 V voltage source on the primary side, and a 5 Ω resistor on the secondary. A current of 22 amps of current is measured to flow through the 5 Ω resistor on the secondary side. The real power flowing into the transformer primary is measured at 2500 W. You can neglect Lm and Rc (the magnetizing inductance and core...
A transformer connected to a 120 V (rms) a line is to supply 12.0 V (rms) to a 5.00 Ohm resistor in the secondary circuit. (a) What should the ratio of turns of the primary to secondary circuit of the transformer be? (b) What is the average power delivered to the secondary? (c) Assuming the transformer to be ideal (i.e., 100% of the power in the primary is transferred to the second), what is the rms current in the primary?
An ideal step-down transformer has a primary coil of 370 turns and a secondary coil of 22 turns. Its primary coil is plugged into an outlet with 115 V, from which it draws a current of 0.29 A. (a) What is the voltage in the secondary coil? (b) Calculate the current in the secondary coil? (c) Assuming that the transformer secondary is driving a resistive load, calculate the average power dissipated in the resistor.
An ideal step-down transformer has a primary coil of 400 turns and a secondary coil of 25 turns. Its primary coil is plugged into an outlet with 110 V(AC), from which it draws an rms current of 0.83 A. 1.)What is the voltage in the secondary coil? 2.)Calculate the rms current in the secondary coil. 3.)Assuming that the transformer secondary is driving a resistive load, calculate the average power dissipated in the resistor.
Please show any equation manipulation.
Problem 6 Your TV's screen uses 4800 (V) of voltage to operate. To provide 4800 (V), inside your TV there is a transformer that converts wall outlet of 120 (V) to 4800 (V) reaching to the TV screen. The secondary coil of this transformer has 9200 turns. Your TV's screen connected to secondary coil of transformer uses 240 (W) of power. A) Calculate current in secondary coil. B) Is this transformer a step-up or a...
Problem E1.2.6 (20 points) Consider the magntically coupled circuit that involves an ideal transformer as depicted in Figure E1.2.6. The sinusoidal voltage source frequency is 20 x 103 (rad/sec). The load connected to the secondary winding (RHS of the ideal transformer) consists of a variable resistor R in series with a variable capacitor C. (a) Find the values of R and C for maximum power transfer from the voltage source in the primary winding. (b) What is the maximum average...