Mental Math The area of the cross section shown is 70 yd? What is the height...

Question

Question

math algebra

Answer 1

Answer #1

In A ABC xoxh=70 h_742 h=14 yee Height of Pyramid=14 yd ?

Answer 2

Similar Homework Help Questions

the cross section of a bearing block is shown in the figure by the shaded area....

the cross section of a bearing block is shown in the figure by the shaded area. calculate the moment of inertia of the section about its base a-a. Appendix A, Problem A/052 Multistep The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. 8" 5 8" 23" Part 1 The cross section is made of three parts: a rectangle (Area 1), a...
The cross section of a bearing block is shown in the figure by the shaded area....

The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. 6" 3" 15* 1804 Answer: Ia-a F in. The number of significant digits is set to 3; the tolerance is +/-2%
(a) A pyramid has a height of 458 ft and its base covers an area of...

(a) A pyramid has a height of 458 ft and its base covers an area of 14.0 acres (see figure below). The volume of a pyramid is given by the expression where B is the area of the base and h is the height. Find the volume of this pyramid in cubic meters. (1 acre 43,560 ft) m3 What If? If the height of the pyramid were increased to 517 ft and the height to base area ratio of the...

Please do everything neetly 5. An open tank of very large cross section area cross section...

Please do everything neetly 5. An open tank of very large cross section area cross section area a A is filled with water to a height 6.5 cm2 tank allows bott n the bottom of the tank allows water to dran id at is the volume flow rate at which water flows out b) At what distance below the bottom of the tank is the cross- one-half of the area of the hole? If A-10000a, how long will it take...
Figure P3.18(not drawn to scale 3.19 A shear force V20 kN acts on the thin cross...

Figure P3.18(not drawn to scale 3.19 A shear force V20 kN acts on the thin cross section shown in Figure P3.19. The cross section has a uniform thickness of 10 mm. Determine the equation of shear flow along the center- lines and sketch it. 100 mm 25 mm 25 mm Figure P3.19(not drawn to scale)
For the remaining problems, consider a cantilevered circular beam with the cross-section shown at...

For the remaining problems, consider a cantilevered circular beam with the cross-section shown at x-8 in. The part made of AISI 1050 cold drawn steel (this is a carbon steel). The two forces and torque are on the right end. Note units on loads and dimensions. Di Not to scale 8 in IC 11. What is the value for ka used in correcting the endurance limit? 12. If L = 12 in, P = F = 0, T varies sinuosidally...

The beam has the rectangular cross section shown.

The beam has the rectangular cross section shown.Part A If w = 3kN/m, determine the maximum bending stress in the beam. Wood used for the beam has an allowable bending stress of ơ=6MPa (Figure 1) Part A Determine the minimum dimension d of the beams cross sectional area.
need help asap!! A beam is constructed with the cross section shown. There Nutra A (NA)...

need help asap!! A beam is constructed with the cross section shown. There Nutra A (NA) is shown and not drawn to scale. The moment of inertia of the cross section about its Neutral Aisi RA - 59.278 in 4 The shear load, V-850 lb. 1 in 3 in V NA Determine the magnitude of the Transverse Shear Stress at point Bit point Bles on the in. x4 in vertical member it in.) Determine the magnitude of the Transverse Shear...
own below is loaded as shown. The beam is made out of a hollow steel rectangular cross-section. Determine: The most economical cross-section that can be below. The a) used if Ơall-30 ksi. Select...

own below is loaded as shown. The beam is made out of a hollow steel rectangular cross-section. Determine: The most economical cross-section that can be below. The a) used if Ơall-30 ksi. Select from the table shown Weight per foot of the cross-section is shown below in the table. 60 in. 40 in. 500 lbs The 1st number indicates the height of the cross-section in inches. 30 in. 250 lbs Izz Wt/Ft. (in) (in') (lbs/ft.) 7.80 12.21 Area Section 304...

The cross-section of a beam is shown below. The top rectanular piece of the cross-section is...

The cross-section of a beam is shown below. The top rectanular piece of the cross-section is a steel section 6 inches wide by 8 inches deep. The dimensions of the member are shown below in the table. The cross-section is loaded in bending by a moment about the zz-axis. The allowable bending stress of the cross-section is 42 (ksi). Determine: a) the elastic centroid of the cross-section. b) the yield moment. c) the plastic centroid of the cross-section d) the...