11. Why the smaller the reinforcing bar, the lesser the development length of the bar?

Question

Question

engineering Civil-Engineering

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

Need help for those 2 questions 9.9. A No. 32 (metric designation) reinforcing bar for concrete...

Need help for those 2 questions 9.9. A No. 32 (metric designation) reinforcing bar for concrete has a diameter of 32 mm. The bar is cut to length in a shear a ratus as shown. The required force P for the shearing operation 300 kN. Determine the ultimate shear strength s vay for this bar ppa- No. 32 reinforcing bar 9.15. A short compression member 2 in. by 2 in. in cross section and 8 in. long is subjected to...
A 150 foot long footing has 3 ea. #5 reinforcing bars continuous the length of the...

A 150 foot long footing has 3 ea. #5 reinforcing bars continuous the length of the footing. The bars are 20 foot long each and the design requires a 30 bar diameter lap splice at each splice. If #5 reinforcing weighs 1.04 pounds per linear foot and has a bar diameter of 5/8 inch, how many tons of rebar are in the footing? (Note: 1 ton = 2,000 pounds) Disregard concrete cover.
must be langer 11 The length of the high C baris 30.0 cm. What is the length of the low C bar (this is the one has...

must be langer 11 The length of the high C baris 30.0 cm. What is the length of the low C bar (this is the one has half the frequency of the high C bar)? a. 15.0 cm .21.2 cm c. 42.4 cm 60.0 cm

Why entrepreneur with lesser disclosure requirement comparision with manager is one of the reason why entrepreneur...

Why entrepreneur with lesser disclosure requirement comparision with manager is one of the reason why entrepreneur has less conflict as compared to a manager. ( 400 words )
Explain the self-reinforcing cycle and why it has negative implications for the economy's growth and employment?

Explain the self-reinforcing cycle and why it has negative implications for the economy's growth and employment?
#1 A bar of mass m and length 2d sits on a peg that is at...

#1 A bar of mass m and length 2d sits on a peg that is at a distance d from the end of the bar. If a force of F is applied downward at a point d/2 from the end, what is the resulting torque? a. Fd/2, b.Fd, c. 2Fd, d.3Fd/2 #2 The same bar of mass m of length 2d sits on a peg that is at a distance d/2 from the end of the bar. If a force...

2. Explain why the addition of higher concentrations of substrate to the enzyme has lesser effect.

2. Explain why the addition of higher concentrations of substrate to the enzyme has lesser effect.
A mobile consisting of a horizontal bar of length 70cm and negligible mass from which two...

A mobile consisting of a horizontal bar of length 70cm and negligible mass from which two decorations are hung up by light strings. The bar is suspended by a vertical wire. Assume two significant digits in the given data. a) How far from the left-hand end of the wire is the vertical wire attached? b) What is the magnitude of the tension in the wire? Figure 11-60 Question 11-55. 1-56 Figure 11-61 shows a mobile consisting of a horizontal bar...
Using a bar length μ

Using a bar of length μ, you are going to lay out a square plot in which the length of each side will be length μ. Thus the area of the plot will be μ2. However, you do not know the value of μ and so you decide to make 15 independent measurements of the bar, {Xi : i = 1, … , n}. Assume that each Xi has mean μ (unbiased measurement) and variance σ2 = 0.4.(a)Find the bias of the random variable X_2 as an estimator for μ2.(b)For what value of k is the estimator X_2 − kS2 unbiased...

A slender bar of length / is pinned to the L-shaped bar at O. The L-shaped...

A slender bar of length / is pinned to the L-shaped bar at O. The L-shaped bar rotates about the vertical axis with a constant angular velocity ω。. Find the acceleration of the mass center of the slender bar for a constant angle β relative to the vertical Indicate your solution in the coordinate system aligned with the bar. #1. a0db