Homework Answers
Add Answer to:
7-2. An aluminum machine part of nominal diameter D 8 cm at 25°C is measured by...
2 parts thx 1. A flat aluminum plate has a circular hole of diameter 1.858 cm...
2 parts thx 1. A flat aluminum plate has a circular hole of diameter 1.858 cm at 0.00 °C.What is the change in its diameter when the temperature of the plate is increased to 114 °C? For reference, the coefficient of thermal expansion for aluminum is 2.3 x 10-5/C°. Give at least 2 significant figures in your answer, which should be in cm. 2.A flat plate made of an unknown metal has a circular hole of diameter 3 cm at...
13. The resistivity of aluminum at 25 'C has been measured to be 2.72 x 10-8 0 m. The thermal coefficient of resistivity of aluminum at 0 C is 4.29 x 10-3 K-1. Aluminum has a valency of 3, a d...
13. The resistivity of aluminum at 25 'C has been measured to be 2.72 x 10-8 0 m. The thermal coefficient of resistivity of aluminum at 0 C is 4.29 x 10-3 K-1. Aluminum has a valency of 3, a density of 2.70 g cm3, and an atomic mass of 27 a. Calculate the resistivity of aluminum at-40°С. (Ans: 2.03 x 103 Ω m) b. What is the thermal coefficient of resistivity at-40'C? (Ans: 5.23x 103K c. Estimate the mean...
an aluminum sphere with an 8 cm diameter is exposed to 60C air with convection heat...
an aluminum sphere with an 8 cm diameter is exposed to 60C air with convection heat transfer coefficient of 35 W/m^2 K. the initial temperature of the phsere is 5 C. a. computer the biot number. b. computer the temperature at the center of the sphere after 5.5 min exposure to the hot air. c. confirm that the lump application is valid.
OAsk Your Teacher 2. +1/3 polnts | Previous Answers SF6 10.P.015 My Notes A brass ring of diameter 10 cm at 18.0°C is heated and slipped over an aluminum rod with a diameter of 10.01 cm at 18.0°C. As...
OAsk Your Teacher 2. +1/3 polnts | Previous Answers SF6 10.P.015 My Notes A brass ring of diameter 10 cm at 18.0°C is heated and slipped over an aluminum rod with a diameter of 10.01 cm at 18.0°C. Assume that the average coefficients of linear expansion are constant (a) To what temperature must this combination be cooled to separate them? PC Is this temperature attainable? yes no (b) If the aluminum rod were 10.03 cm in diameter, what would be...
A pin fin is made of an Aluminum (k=235W/m K) rod length 68 cm and diameter...
A pin fin is made of an Aluminum (k=235W/m K) rod length 68 cm and diameter 10 mm. If the heat transfer coefficient is 10 W/m2 K, calculate the fin efficiency. a. 27% b. 46% c. 35% d. 56% e. 97% f. None of them A 2-m-high, 3-m-wide, and 120-cm-thick wall of a house has a thermal resistance of 0.0124 ºC/W. The thermal conductivity of the wall is a. 0.72 W/mºC b. 1.1 W/mºC c. 1.6 W/mºC d. 16 W/mºC...
1. Ferrous metals include which of the following A Aluminum B. Copper C Gold D. Steel...
1. Ferrous metals include which of the following A Aluminum B. Copper C Gold D. Steel 2. The two categories of metals that are based onion (Fe) are A Aluminum Alloy & Castle B. Chromium & Nickel C. Manganese & Vanadium D. Cast Iron & Steel 3. Aluminum Alloy, Nickel Alloy, Zinc Alloy, and Titanium Alloy are cumples of A Nonferrous Metals B.Ceramics C Superllos D. Carmets 4. In the heating of most metal alloys melting begins at a certain...
Problem 2 A 4 mm diameter and 20 cm long aluminum fin (k 240 W/m-K) is...
Problem 2 A 4 mm diameter and 20 cm long aluminum fin (k 240 W/m-K) is attached to a surface. If the heat transfer coefficient is 12 W/m2 K, determine the percent error in the rate of heat transfer from the fin when the infiniely long fin assumption is used nstead of the adiabatic fin tip assumption. D-4 mm L- 10 cm Fig. 2 fin
It is desired to evaluate the tensile properties of an aluminum alloy. A tensile test is...
It is desired to evaluate the tensile properties of an aluminum alloy. A tensile test is performed using a standard cylindrical tensile specimen with a diameter of 12.8 mm and a gauge length of 50.800 mm. The gage length and final diameter of the sample are measured after the sample is removed from the testing machine. The gage length and the diameter of the necked region after the specimen was removed from the testing machine are 60 mm and 9...
Problem 3 (25 pts.) A J-type thermocouple is calibrated against an RTD standard to within +0.02°C...
Problem 3 (25 pts.) A J-type thermocouple is calibrated against an RTD standard to within +0.02°C between 0° and 200°C. The emf is measured with an A/D converter having a resolution of 0.075 mV. The reference junction temperature is provided by an ice bath. The calibration procedure yields the following linear equation: T(°C) = 0.11 + 19.2V ,where the units of voltage Vis mV. This first order curve fit has an error of 0.5°C. Part a) 15 pts. Find the...
Problem 3 (25 pts.) A J-type thermocouple is calibrated against an RTD standard to within +0.02°C...
Problem 3 (25 pts.) A J-type thermocouple is calibrated against an RTD standard to within +0.02°C between 0° and 200°C. The emf is measured with an A/D converter having a resolution of 0.075 mV. The reference junction temperature is provided by an ice bath. The calibration procedure yields the following linear equation: T(°C) = 0.11 + 19.2V ,where the units of voltage Vis mV. This first order curve fit has an error of 0.5°C. Part a) 15 pts. Find the...
13. The resistivity of aluminum at 25 'C has been measured to be 2.72 x 10-8 0 m. The thermal coefficient of resistivity of aluminum at 0 C is 4.29 x 10-3 K-1. Aluminum has a valency of 3, a density of 2.70 g cm3, and an atomic mass of 27 a. Calculate the resistivity of aluminum at-40°С. (Ans: 2.03 x 103 Ω m) b. What is the thermal coefficient of resistivity at-40'C? (Ans: 5.23x 103K c. Estimate the mean...
OAsk Your Teacher 2. +1/3 polnts | Previous Answers SF6 10.P.015 My Notes A brass ring of diameter 10 cm at 18.0°C is heated and slipped over an aluminum rod with a diameter of 10.01 cm at 18.0°C. Assume that the average coefficients of linear expansion are constant (a) To what temperature must this combination be cooled to separate them? PC Is this temperature attainable? yes no (b) If the aluminum rod were 10.03 cm in diameter, what would be...
1. Ferrous metals include which of the following A Aluminum B. Copper C Gold D. Steel 2. The two categories of metals that are based onion (Fe) are A Aluminum Alloy & Castle B. Chromium & Nickel C. Manganese & Vanadium D. Cast Iron & Steel 3. Aluminum Alloy, Nickel Alloy, Zinc Alloy, and Titanium Alloy are cumples of A Nonferrous Metals B.Ceramics C Superllos D. Carmets 4. In the heating of most metal alloys melting begins at a certain...
Problem 2 A 4 mm diameter and 20 cm long aluminum fin (k 240 W/m-K) is attached to a surface. If the heat transfer coefficient is 12 W/m2 K, determine the percent error in the rate of heat transfer from the fin when the infiniely long fin assumption is used nstead of the adiabatic fin tip assumption. D-4 mm L- 10 cm Fig. 2 fin
Problem 3 (25 pts.) A J-type thermocouple is calibrated against an RTD standard to within +0.02°C between 0° and 200°C. The emf is measured with an A/D converter having a resolution of 0.075 mV. The reference junction temperature is provided by an ice bath. The calibration procedure yields the following linear equation: T(°C) = 0.11 + 19.2V ,where the units of voltage Vis mV. This first order curve fit has an error of 0.5°C. Part a) 15 pts. Find the...
Problem 3 (25 pts.) A J-type thermocouple is calibrated against an RTD standard to within +0.02°C between 0° and 200°C. The emf is measured with an A/D converter having a resolution of 0.075 mV. The reference junction temperature is provided by an ice bath. The calibration procedure yields the following linear equation: T(°C) = 0.11 + 19.2V ,where the units of voltage Vis mV. This first order curve fit has an error of 0.5°C. Part a) 15 pts. Find the...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 11 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 11 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 11 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 11 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 11 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 11 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 11 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 11 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 11 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 11 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 11 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 11 months ago