Homework Answers
Using
fbd and applying shear stress formula to get the result.
Add Answer to:
1.7 LIMIT STATE DESIGN 55 1 F1-22. The pin is made of a material having a...
The pin is made of a material having a failure shear stress of Ttail 120 MPa...
The pin is made of a material having a failure shear stress of Ttail 120 MPa Part A Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of FS 2.5 against shear failure. 80 KN Tap image to zoom Express your answer as an integer and include the appropriate units d= Value ! Units SubmitRequest Answer
2. The rod is made of a material having a yield stress oy = 250 MPa....
2. The rod is made of a material having a yield stress oy = 250 MPa. Determine the minimum required diameter for its sections take at segments AB and BC. Apply a factor of safety F.S. = 1.5 against yielding. 600 mm mm 1 ZA 40 KN 50 KN
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts...
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is fail = 350 MPa. Use a factor of safety for shear of F.S. = 2.5. 30 mm 80 KN 30 mm 40 KN 40 KN
6. The clevis supports a pin. The attached rod is subjected to a tensile load of...
6. The clevis supports a pin. The attached rod is subjected to a tensile load of 80 kN. If the maximum shear stress the material can support is 20 MPa, determine the required pin diameter to produce a factor of safety of 2.5. (12) 80 kN
The rods AB and CD are made of steel having a failure tensile stress of O...
The rods AB and CD are made of steel having a failure tensile stress of O fail = 510 MPa. Using a factor of safety of F.S. = 1.75 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. В. D 6 kN 5 kN 4 kN A C 4 2 m ----2m- -3 m -3 m Figure: 07_PROB_076
The 5m beam is supported by a pin in double shear at Cand cable AB. The...
The 5m beam is supported by a pin in double shear at Cand cable AB. The cable has a tension of 40.7 kN and is subjected to the point loads shown. Design a pin diameter at C to the closest mm so that it will not fail under shear stress. Use a yield shear stress of 160 MPa and a F.S. against yield of 2. 3.7KN PPKN 14.8KN 74 KW .5 1.5m 1,5m 40.7KN A CS Scanned With CamScanner- O...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power a...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
Having issues? See our FAQ Guide QUESTION 1 1. Required Pin Diameter for a Frame The...
Having issues? See our FAQ Guide QUESTION 1 1. Required Pin Diameter for a Frame The frame shown supports a mass of 500 kg. Determine the diameter of the pin in [mm] at joint A for a factor of safety of 3. Assume fat allowable shear stress for the pin is 150 MPa and that the joint is a single shear type. 2m + 2m А С B 2 m ID 500 kg 2 m E
Please take P=1501.6 N Remaining time: 145:05 1 2 3 4 5 6 Question 6 Force...
Please take P=1501.6 N
Remaining time: 145:05 1 2 3 4 5 6 Question 6 Force of P = 1500 + S N is applied to the rigid arm ABC as shown in the figure. Determine the average shear stress developed in the 6-mm diameter pin B that is subjected to double shear. What is the minimum required diameter d of steel rod CD to the nearest mm. Apply a factor of safety F.S. = 1.5 against yielding. 0,= 300...
2. If the solid shaft is made from material having an allowable shear stress of Tallowable...
2. If the solid shaft is made from material having an allowable shear stress of Tallowable = 60 MPa, determine the required diameter of the shaft. 15 kN-m 30 kN m 75 kN-m 30 kN-m QUESTION 5 Problem 2: What is the maximum internal torque in the shaft? 45 kN-m 120 kN-m 25 kN-m 75 kN-m N QUESTION 6 Problem 2: What is the minimum diameter of the solid shaft? O 207 mm O 156 mm O 168 mm 132...
The pin is made of a material having a failure shear stress of Ttail 120 MPa Part A Determine the minimum required diameter of the pin to the nearest mm. Apply a factor of safety of FS 2.5 against shear failure. 80 KN Tap image to zoom Express your answer as an integer and include the appropriate units d= Value ! Units SubmitRequest Answer
2. The rod is made of a material having a yield stress oy = 250 MPa. Determine the minimum required diameter for its sections take at segments AB and BC. Apply a factor of safety F.S. = 1.5 against yielding. 600 mm mm 1 ZA 40 KN 50 KN
4- The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is fail = 350 MPa. Use a factor of safety for shear of F.S. = 2.5. 30 mm 80 KN 30 mm 40 KN 40 KN
6. The clevis supports a pin. The attached rod is subjected to a tensile load of 80 kN. If the maximum shear stress the material can support is 20 MPa, determine the required pin diameter to produce a factor of safety of 2.5. (12) 80 kN
The rods AB and CD are made of steel having a failure tensile stress of O fail = 510 MPa. Using a factor of safety of F.S. = 1.75 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. В. D 6 kN 5 kN 4 kN A C 4 2 m ----2m- -3 m -3 m Figure: 07_PROB_076
The 5m beam is supported by a pin in double shear at Cand cable AB. The cable has a tension of 40.7 kN and is subjected to the point loads shown. Design a pin diameter at C to the closest mm so that it will not fail under shear stress. Use a yield shear stress of 160 MPa and a F.S. against yield of 2. 3.7KN PPKN 14.8KN 74 KW .5 1.5m 1,5m 40.7KN A CS Scanned With CamScanner- O...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
Having issues? See our FAQ Guide QUESTION 1 1. Required Pin Diameter for a Frame The frame shown supports a mass of 500 kg. Determine the diameter of the pin in [mm] at joint A for a factor of safety of 3. Assume fat allowable shear stress for the pin is 150 MPa and that the joint is a single shear type. 2m + 2m А С B 2 m ID 500 kg 2 m E
Please take P=1501.6 N
Remaining time: 145:05 1 2 3 4 5 6 Question 6 Force of P = 1500 + S N is applied to the rigid arm ABC as shown in the figure. Determine the average shear stress developed in the 6-mm diameter pin B that is subjected to double shear. What is the minimum required diameter d of steel rod CD to the nearest mm. Apply a factor of safety F.S. = 1.5 against yielding. 0,= 300...
2. If the solid shaft is made from material having an allowable shear stress of Tallowable = 60 MPa, determine the required diameter of the shaft. 15 kN-m 30 kN m 75 kN-m 30 kN-m QUESTION 5 Problem 2: What is the maximum internal torque in the shaft? 45 kN-m 120 kN-m 25 kN-m 75 kN-m N QUESTION 6 Problem 2: What is the minimum diameter of the solid shaft? O 207 mm O 156 mm O 168 mm 132...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 11 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 11 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 11 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 11 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 11 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 11 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 11 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 11 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 11 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 11 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 11 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 11 months ago