A rod has a 1.3 m long section that is cast iron and a 2.6 m...

Question

Question

A rod has a 1.3 m long section that is cast iron and a 2.6 m long section that is aluminum as shown in the diagram below. 0.2

science physics

Answer 1

Answer #1

solumon Young modulus Stress Strain » Y. FA - Рxt. AXAL AL 2 -> AL= F. L AXY ah= FXL (482xY lo X 206 fos cast iron, Aby = 8.1

Answer 2

Similar Homework Help Questions

My Notes A rod has a 1.3 m long section that is cast iron and a...

My Notes A rod has a 1.3 m long section that is cast iron and a 2.6 m long section that is aluminum as shown in the diagram below 020 cm Rod 1 13m The diameter of the cylindrical rod is 0.40 cm. Yt subjected to a force of 7.3 x 103 N -100 x 1010 N/m2 and Y u 7x 1010 N/m2. How much elongation (in cm) is produced in the rod when it is cm My Notes A...
1. A 2-cm diameter gra y cast iron-class 20 solid round beam of 1-m long is...

1. A 2-cm diameter gra y cast iron-class 20 solid round beam of 1-m long is cantilevered at one end and is subjected to a 100 N load at the other end. The beam is resting on a roller support in the middle. Determine the reactions at the wall. (15 points)
An elastic rod has the length of 1 m and cross-section area of 0.1 m2 ....

An elastic rod has the length of 1 m and cross-section area of 0.1 m2 . This rod has a force constant of 1010 N/m. A second rod, made of the same material, has the length of 2 m and cross-section area of 0.3 m2 . What is its force constant (in unit of 1010 N/m)?

A heat conducting rod, is made of an aluminum section that is 0.10 m long, and...

A heat conducting rod, is made of an aluminum section that is 0.10 m long, and a copper section that is 0.80 m long. Both sections have cross-sectional areas of 0,0004 m2. The aluminum end is maintained at a temperature of 20°C and the copper end is at 121°C. The thermal conductivity of aluminum is 205 W/m∙K and of copper is 385 W/m∙K. Steady state has been reached, and no heat is lost through the well-insulated sides of the rod....
A cantilever cast-iron beam is 6 ft long and has a “T” cross section, as shown....

A cantilever cast-iron beam is 6 ft long and has a “T” cross section, as shown. Calculate the maximum tensile and compressive bending stresses. The applied load is 450 lb. Neglect the weight of the beam. Show the diagram of both (Tensile and Bending stresses at the section area). 450 lb 60" (a) Load diagram (b) Section A-A
Paton P'S 2 107 3.6 The inlet of a cast iron pipe, 120 m long and...

Paton P'S 2 107 3.6 The inlet of a cast iron pipe, 120 m long and 150 mm a dam. The pipe is 1/25 slope and contains a 90 bend (R/d = 1,0) diameter is 2 m below the wa.ter level of laid with a and the water exits to the atmosphere. Take the water temperature B.S 20 C (then 10 kg/ms) and determine the flow rate. [0,045 m2/s] 3.7 Water is discharged from a reservoir through a sharp outlet...

Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240...

Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
A force of 6024 N is applied outwardly to each end of a 6-m long rod...

A force of 6024 N is applied outwardly to each end of a 6-m long rod with a radius of 42 mm and a Young's modulus of 125 x 108 N/m2. What is the elongation of the rod (in mm)?
Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and...

Problem 4 (50 points) water is discharged from a reservoir at a rate of 18.103 m2/s using two horizontal cast iron pipes nected in series and a pump between them. The first pipe is 20 m long and has a 6-cm diameter, while the second pipe is 35 m long and has a 4-cm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged. Losses associated with the connection...

On a part time job you are asked to bring a cylindrical iron rod of density 7800 kg/m^3, length 81.2 cm and diameter 2.7...

On a part time job you are asked to bring a cylindrical iron rod of density 7800 kg/m^3, length 81.2 cm and diameter 2.75 cm from a storage room to a machinist. Calculate the weight of the rod, w. The acceleration due to gravity, g= 9.81 m/s^2. w= 36.9 N Part A Part B) Now that you know the weight of the rod, do you think that you will be able to carry the rod without a cart? Yes or...