In the drawing, water flows from a wide section of a pipe to a narrow section....

Question

Question

In the drawing, water flows from a wide section of a pipe to a narrow section. In which part of the pipe is the volume flow rate the greatest?

science Advanced-Physics

Answer 1

✔ Recommended Answer

Answer #1

Volume flow rate is same in both the cross-sections due to mass conservation.
Velocity will be lower in area where flow is wider.

Answer 2

Similar Homework Help Questions

11. (10 pts). Water flows through a horizontal pipe with an inner diameter of 5.22 cm...

11. (10 pts). Water flows through a horizontal pipe with an inner diameter of 5.22 cm at a speed of 6.63 m/s. The pipe eventually widens to a diameter of 8.81 cm. a) Determine the volume flow rate for the water. b) How fast is the water moving in the wide portion of the pipe? c) What is the kinetic pressure in each portion of the pipe? d) Did the water pressure change in the wide portion of the pipe...
Suppose water flows from a narrow pipe (pipe X) at low elevation into a wider pipe...

Suppose water flows from a narrow pipe (pipe X) at low elevation into a wider pipe (pipe Y) at higher elevation. What can you conclude about the fluid pressures in the two pipes? Assume that water behaves as an ideal fluid cross out Select one: O a. there is insufficient information to draw a conclusion O b. pressure in pipe Y is equal to the pressure in X C. pressure in pipe Y is less than the pressure in X...
through the tunnel at a speed of 3.0 m/s until it reaches a narrow section where...

through the tunnel at a speed of 3.0 m/s until it reaches a narrow section where the tunnel's diameter is 2.70 m. The pressure in the narrow section is 82 kPa. Use the continuity equation to find the water's speed in the narrow section of the tunnel. Then find the pressure in the wide portion of the tunnel. An enormous open vat owned by a British cider company has a volume of nearly 7000 m3. If a small hole is...

An incompressible fluid is flowing through a vertical pipe with a constriction. The wide section is...

An incompressible fluid is flowing through a vertical pipe with a constriction. The wide section is 2.00 cm in diameter and is at the top of the pipe. The pressure of the fluid in the wide section at the top is 200 kPa. The velocity of the fluid in the wide section is 4.00 m/s. The narrow section is located 2.00 m below the wide section. What is the diameter of the narrow section, if the pressure of the fluid...
Problem 3. Water flows in a horizontal section of a 20m long pipe. The pipe has...

Problem 3. Water flows in a horizontal section of a 20m long pipe. The pipe has a diameter of 0.1m. Determine the velocity of the flow in the pipe if the pipe is made of wrought iron (Esteel pipe = 0.00004m) and the pressure difference is 165kPa over the 20m length.
Water at 10 ◦C flows in a pipe from a house to a guest house. On...

Water at 10 ◦C flows in a pipe from a house to a guest house. On cold winter days the pipe loses an estimated 500W of heat transfer. To keep the water from freezing, and possibly breaking the pipe, it must continuously flow in the pipe. Determine the minimum required mass flow rate that will ensure that the water does not freeze (i.e., reach 0 ◦C)? 6. (10 points) Water at 10 °C flows in a pipe from a house...

Consider a water pipe with a restricted section as illustrated beside. The consumption meter from the...

Consider a water pipe with a restricted section as illustrated beside. The consumption meter from the utility company indicates a constant water flow of 480 L/min. You also know that the pipe has a diameter of 40 cm at the inlet and outlet but only a diameter of 20 cm in the restricted region. • B) What is the water column height above the restricted section of the pipe (that’s h2)? C) What is the highest value (in kPa) of...
A soft drink (mostly water) flows in a pipe at a beverage plant with a mass...

A soft drink (mostly water) flows in a pipe at a beverage plant with a mass flow rate that would fill 220 0.355 - L cans per minute. At point 2 in the pipe, the gauge pressure is 152kPa and the cross-sectional area is 8.00cm2. At point 1, 1.35m above point 2, the cross-sectional area is 2.00cm2. Part a Find the mass flow rate. kg/s part b Find the volume flow rate. L/s part c Find the flow speed at...
9. Water (density 1.0 X 10 kolm flows through a horizontal tapered pipe. At the wide...

9. Water (density 1.0 X 10 kolm flows through a horizontal tapered pipe. At the wide ends speed is 4 m/s. The difference in pressure between the two ends is 4.5 x 10' Pa. The speed of the water at the narrow end is: A. 2.6 m/s B.3.2 m/s C. 4.0 m/s D. 4.5 m/s E.5.0 m/s - nne with twice the radius of the other. of the water

Water at 10℃ flows with a Re of 1400 in a circular cross section pipe with...

Water at 10℃ flows with a Re of 1400 in a circular cross section pipe with a diameter of 8cm. Calculate a) The flow rate b) The pressure drop over a 3m length c) The velocity at r= 2cm d) The maximum velocity 7:07 ൽ ഇ ം .. 59% പ Wart 4 1K it in a Recognize