HomeworkLib
Question

Power can be measured in a circuit using either of the following strategies relation: P1*2*R or P-V*1. If you have the following three instraments with the given specifications, which of measuring power will have more accurate resulht for power? Show your solution steps (Hint assume valucs for V, 1, R you could use 100V,SA, 20 Ω) Resolutio 1.0 m V 1.0 Ohm 0.1 A %error in readout 0.5% 0.1% 0.5 % Voltmeter Ohmmeter
engineering   Mechanical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

aNeh in sLument 0 Ammeic* I: SA e need tu find the SLYqteg which sive e4 deviathon or fact LeL: AII instru men Cal culcted pwr1 2. ConSide Strates p VI .. :/.emo γ in P«we γ - -1.0025 . sinceソ.er0 γ 1n power fo γ oweY

0 0
Add a comment
Know the answer?
Add Answer to:
Power can be measured in a circuit using either of the following strategies relation: P1*2*R or...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • Part 2 Maximum Power Transfer (Validating the Condition R = Rth) (a) Construct the network of...

    Part 2 Maximum Power Transfer (Validating the Condition R = Rth) (a) Construct the network of Fig. 11.7 and set the potentiometer to 50 2. Measure the voltage across R as you vary Rthrough the following values: 50, 100, 200, 300, 330, 400, 600, 800, and 1000 12. Be sure to set the resistance with the ohmmeter section of your meter be fore each reading. Remember to turn off the dc supply and disconnect one terminal of the po tentiometer...

  • can you sovle this problem, also I need the code for part d. thanks Problem #5 Ri Vy= Probe I R- 1502 o VOLTMETER IN...

    can you sovle this problem, also I need the code for part d. thanks Problem #5 Ri Vy= Probe I R- 1502 o VOLTMETER INPUT CIRCUIT Probe 2 Express resistance in ohms (2) and voltage in volts (V) Requirements-Part 1 (voltmeter not attached yet) a) Suppose you want to produce a voltage of 1 V across resistor R2 (i.e. Vor 1 V) Use the voltage divider equation to find the value of Ri that is needed to do this. b)...

  • 1 K CH.1 CH.2 Problems (13-14): The circuit above with an unknown impedance was connected to a function generator, and the scope picture at the left was saved. Your lab partner claims he w...

    1 K CH.1 CH.2 Problems (13-14): The circuit above with an unknown impedance was connected to a function generator, and the scope picture at the left was saved. Your lab partner claims he wrote down the scales on the oscilloscope and the unknown component values, but now says he can't find them. However, you remember that the larger waveform is Channel 1, and that the frequency was 500 Hz 13. The horizontal time scale is (a) 0.5 ms/div (c) 4...

  • Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 an...

    Notes for lab dc02-Resistors and the Color Code will skip are Part 2 e, g: Part 4; Exercises 2, 4,5,6 and 3. It is important to answer the exercises correctly in each labl you should include the appropriate prefix for the unit in the Numerical Value We will not be Volt using the Volt-Ohm meter (VOM) for this lab, so skip the parts that ask for VOM measurements. The parts we You do need to complete Exercises1 Note that in...

  • 1. Why can the DSO only measure node voltages when the Function Generator is the power supply in ...

    1. Why can the DSO only measure node voltages when the Function Generator is the power supply in a circuit (unless it is using a current probe)? 2. Consider Figure 1. According to the calculations in the lab handout, if Z-1kΩ +/6914, then the phase difference (фи-фі) between u(t) and i (t) is 34.6". a. If this v(t) and i(t) were displayed on a DSO (v(t) being a node voltage and using a current probe for i(t) as shown in...

  • I am working on my Physics lab report where it was all about Direct Current Measurement...

    I am working on my Physics lab report where it was all about Direct Current Measurement and Ohm’s Law. We had 5 different resistors and had to construct different circuits using a power supply, volt-ohm-milliammeter (VOM) and a digital multimeter to get measurements of resistance, voltage, and current. Nominal values of resistance and tolerance Resistor Nominal Resistance (Ohms) Tolerance (Ohms) R1 680 +/- 68 R2 1000 +/- 50 R3 1500 +/- 75 R4 4700 +/- 470 R5 10,000 +/- 500...

  • summatize the following info and break them into differeng key points. write them in yojr own...

    summatize the following info and break them into differeng key points. write them in yojr own words   apartus 6.1 Introduction—The design of a successful hot box appa- ratus is influenced by many factors. Before beginning the design of an apparatus meeting this standard, the designer shall review the discussion on the limitations and accuracy, Section 13, discussions of the energy flows in a hot box, Annex A2, the metering box wall loss flow, Annex A3, and flanking loss, Annex...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT