HomeworkLib
Question

The micro power grid uses AWG 1/0 size cable as the primary cable to deliver power from generators to transformer. The resistance (RL) of this kind of cable is 0.13 Ohm/1000 ft, and the Reactance (X) at 60 Hz is 0.035 Ohm/1000 ft. Calculate the resistance (Ohm) and inductance (H) for a cable that is 7000 ft long.

engineering   Electrical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

for Cable aklane and rescante are direa are dirce cH I0 00 I0 OD o 00 oherie - inductance tn ttener 0.34Sじの The required rcaract tead Shou서 Be given. 여 ghoud be iver

0 0
Add a comment
Know the answer?
Add Answer to:
The micro power grid uses AWG 1/0 size cable as the primary cable to deliver power...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • 1 A single phase AC system Consider a single phase AC distribution system in which there...

    1 A single phase AC system Consider a single phase AC distribution system in which there a single home connected to a 10kVA service transformer. Let’s assume that the primary of the distribution transformer can be modeled as an ideal 240V (rms) AC source and that the effective impedance of the transformer is 2% resistance and 3% reactance. (See lecture notes for converting % to Ohms). Connected to the secondary of the transformer is 200 ft of #6 AWG aluminum...

  • what information needed? 3. Repeat Example 7.8, using a 100 kVA transformer and #3/0 AWG and...

    what information needed? 3. Repeat Example 7.8, using a 100 kVA transformer and #3/0 AWG and #2 AWG cables for the SLs and SDs, respectively Show the procedure to arrive at the following answers (a) 0.72 pu A (b) 0.050 pu V Example 7.8 residential secondary distribution system. Assume that the distribution trans- Figure 7.11 shows former capacity is 75 kVA (use Table 7.1), all secondaries and services are single-phase three wire, nominally 120/240 V, and all SLs are of...

  • power system A single-circuit 60-Hz high voltage power transmission line is 370 km (230 mi) long....

    power system A single-circuit 60-Hz high voltage power transmission line is 370 km (230 mi) long. The conductors are Rook with flat horizontal configuration and 7.25 ms=(23.8 ft.) conductor spacing. The load on the line is 125 MW at 100% power factor. Use attached Tables A3 to A3to determine; The sending end voltage Vs The sending end current Is The sending end power Ps The percentage voltage regulation The transmission efficiency Given that Ds for the Rook conductor is 0.0327...

  • I need help to solve this questions about Generator Governor Droop and Transmission Line. A complete...

    I need help to solve this questions about Generator Governor Droop and Transmission Line. A complete solutions with answers would be great. Thank you Generation Question 1 to 5 relate to the following grid connected generator. A governor-controlled, steam-driven 450 MW synchronous generator with 5% droop is synchronized to the 60 Hz grid and its load set-point adjusted to deliver 300 MW to the grid. Q1. (a) 000 What is the actual droop of the generating unit? 0.0225 Hz/MW (b)...

  • Accuracy is important. Do not round intermediates and check the answer range to make sure you...

    Accuracy is important. Do not round intermediates and check the answer range to make sure you are correct. Values: [01] 2.08 [02] 68.47 [03] 0.239 [04] 1173.7 [05] 1403. [06] 53.8 THE CORRECT ANSWERS WILL BE IN THE FOLLOWING RANGES: 8-1a. 140, 220 Hz 8-1b. 40:0, 62:0 mA 8-2a. 70:0, 99:0 V 8-2b. 140:0, 160:0 V 8-2c. 60:0, 99:0 V 8-2d. 60:0, 90:0 V 8-3a. 40:0; 99:0 pF 8-3b. 100; 400 mV 8-3c. 1:00; 3:00 mV 8-4a. 100; 150 V...

  • And negligible shunt admittance. Calculate the resistance and reactance from the table on Page 4....

    and negligible shunt admittance. Calculate the resistance and reactance from the table on Page 4. It delivers 500KVA at 2400V to the load and a 0.90 lagging power factor. Calculate the following a) The required sending end voltage b) The required sending end power factor c) The percent voltage regulation at the receiving end SHOW ALL YOUR CALCUALTIONS feet long. 470 eU steel conduit hase dietribution transformer with voltage 2400/240VAC (center I Table 9 Alternating-Curreat Resistunce und Reactance for 600-Volt...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT