![[10] A standard ¼ inch UNC bolt is specified to have a length of 1.25 inches. The screw, is to clamp two 0.2 inch plates with a standard regular hex nut and no washers. 2. a. Is the bolt too short (Yes No) b. Is the bolt too long (Yes No)](http://img.homeworklib.com/questions/65f1f920-173b-11ec-82c0-517b5e899054.png?x-oss-process=image/resize,w_560)
Homework Answers
To tighten the bolt with plate by nut with 1/4 size has maximum thickeness of 0.226 from standard
Then bolt length left after assembly
= 1.25-0.2x2-.226
= 0.624 inch
That is too long
Ans (b)
Add Answer to:
[10] A standard ¼ inch UNC bolt is specified to have a length of 1.25 inches....
Pts) Two objects to be joined, fixed conditions. Geometric tolerance is 0.020 inch at MMC. Minimu...
pts) Two objects to be joined, fixed conditions. Geometric tolerance is 0.020 inch at MMC. Minimum rance between shaft and hole is 0.002, Hole tolerance is 0.0015. Size the top and bottom parts. 0.550/0.560 8). (1Opts) Three blocks are to be joined by a á x 10 UNC bolts and nut. The blocks thickness is 0.875inch, 1.25 inches and 0.750inch. Two plain washers are 0.250 thick. Determine the length of fastener to be used.
pts) Two objects to be joined,...
**Use Shigley's Mechanical Engineering Design, McGraw-Hill textbook as a reference Problem 2: Two identical aluminum...
**Use Shigley's Mechanical
Engineering Design, McGraw-Hill textbook as a reference
Problem 2: Two identical aluminum plates are each 2.5 in thick, and are compressed with one bolt and nut. Washers are used under the head of the bolt and under the nut. Washer properties: steel; ID = 0.75 in; OD = 1.5 in; thickness = 0.095 in. Nut properties: steel; height = 7/16in. Bolt properties: 0.75 in-10 UNC grade 8 Plate properties: aluminum; E10.3 Mpsi; Su=47 kpsi; Sy= 25 kpsi...
[3. (3 marks) Two steel plates each of 1.0 inch thickness (E-30 MPsi) are joined by...
[3. (3 marks) Two steel plates each of 1.0 inch thickness (E-30 MPsi) are joined by SAE grade 8 bolt and no washers. Assume the bolt specification to be 34-10 UNC and bolt length of 2.75 inch. The joint is subjected to a fluctuating load from 1000 lbf to 9000 lbf. The yield strength of the plate material is 60 kpsi. Neglect the stress concentration in the threads of the bolt. Determ ine the following: [a]. whether the bolt is...
5. A holding fixture for a work piece 1.5 inch thick at clamp location is being designed. The detail of one of the clamps is shown in the figure. The spring is required to drive the clamp upward...
5. A holding fixture for a work piece 1.5 inch thick at clamp location is being designed. The detail of one of the clamps is shown in the figure. The spring is required to drive the clamp upward while removing or inserting a work piece. A clamping force of 10 lbf is satisfactory. The base plate is 5/8 inch thick. The clamp screw has a 7/16 in-20 UNF thread. Allow 0.05 inch diametral clearance between screw and the inner coil...
Consider a cut thread bolt shown in Figure 8-17 of your textbook. The bolts are initially...
Consider a cut thread bolt shown in Figure 8-17 of your textbook. The bolts are initially tightened by applying a torque to the nut to induce an initial axial preload for these fasteners. The clamped flanges of the steel housing each 1.25 inch thick. A 3/8-24 UNF SAE Grade 7 steel bolt is considered for this application. Bolt is 20% longer than the clamp length to allow sufficient protrusion for the nut. The external force on the bolted assembly is...
Please show solution for O step by step, use data and ansers for N as given (O)For the bolt of question (N) above, what is the required tightening torque? Answer Box: Torque 141 lb-in Total Clam...
Please show solution for O step by step, use data and ansers
for N as given
(O)For the bolt of question (N) above, what is the required tightening torque? Answer Box: Torque 141 lb-in Total Clamping Force: F,-| 12,000 |lb Number of Bolts: N- Percentage of Proof Strength: PP- 75% SAE Grade 5 Steel Bolt Material Proof Strength of Bolt material: σ a 85,000 psi Lubrication Constant: K 0.15 Results Formula P FrIN Load on each Screw. P- 3000 b...
1. Bowling balls for regular 10-pin bowling are specified to have a diameter between 8.500 and...
1. Bowling balls for regular 10-pin bowling are specified to have a diameter between 8.500 and 8.595 inches A sample of 25 balls has a mean diameter of 8.55 inches and a standard deviation of 0.023 inches Note: You have a sample standard deviation. (a) Construct a 99% confidence interval on the true mean diameter. (b) Construct a 95% confidence interval on the true mean diameter. 2. After a 9-game tournament, our intrepid bowler has recorded a striker percentage of...
(1) A box has a height of 6 inches, a width of 4 inches, and a length of 10 inches (and therefore a volume of 240 cubic inches). The height is decreasing at a rate of 0.5 inches per minute, the width...
(1) A box has a height of 6 inches, a width of 4 inches, and a length of 10 inches (and therefore a volume of 240 cubic inches). The height is decreasing at a rate of 0.5 inches per minute, the width is increasing at a rate of 2 inches per minute, and the length is increasing at a rate of 1 inch per minute. At what rate is the volume changing? Car A travels East towards the intersection of...
A gear has been designed to have a diameter of 3 inches. The standard deviation of the process is 0.3 inch. A control chart is shown. Each chart has horizontal lines drawn at the mean, μ, μ 2o, and a...
A gear has been designed to have a diameter of 3 inches. The standard deviation of the process is 0.3 inch. A control chart is shown. Each chart has horizontal lines drawn at the mean, μ, μ 2o, and at μ 3G. Determine if the process shown is in control or out of control. Explain Is the process in control or out of control? Select all that apply A. Out of control, because a point lies more than three standard...
You have a long piece of 8-inch-wide metal that you plan to make into a gutter by bending up 3 inches on each side (see...
You have a long piece of 8-inch-wide metal that you plan to make into a gutter by bending up 3 inches on each side (see below). The first two steps are about always labeling your picture a) Please label the angle(s) below with a variable. (They're the same) [1 pt] Now label the sides of the blue triangle below in terms of the variable you used in part (a). You'll need to use trigonometry to do this. Of course, show...
pts) Two objects to be joined, fixed conditions. Geometric tolerance is 0.020 inch at MMC. Minimum rance between shaft and hole is 0.002, Hole tolerance is 0.0015. Size the top and bottom parts. 0.550/0.560 8). (1Opts) Three blocks are to be joined by a á x 10 UNC bolts and nut. The blocks thickness is 0.875inch, 1.25 inches and 0.750inch. Two plain washers are 0.250 thick. Determine the length of fastener to be used.
pts) Two objects to be joined,...
**Use Shigley's Mechanical
Engineering Design, McGraw-Hill textbook as a reference
Problem 2: Two identical aluminum plates are each 2.5 in thick, and are compressed with one bolt and nut. Washers are used under the head of the bolt and under the nut. Washer properties: steel; ID = 0.75 in; OD = 1.5 in; thickness = 0.095 in. Nut properties: steel; height = 7/16in. Bolt properties: 0.75 in-10 UNC grade 8 Plate properties: aluminum; E10.3 Mpsi; Su=47 kpsi; Sy= 25 kpsi...
[3. (3 marks) Two steel plates each of 1.0 inch thickness (E-30 MPsi) are joined by SAE grade 8 bolt and no washers. Assume the bolt specification to be 34-10 UNC and bolt length of 2.75 inch. The joint is subjected to a fluctuating load from 1000 lbf to 9000 lbf. The yield strength of the plate material is 60 kpsi. Neglect the stress concentration in the threads of the bolt. Determ ine the following: [a]. whether the bolt is...
5. A holding fixture for a work piece 1.5 inch thick at clamp location is being designed. The detail of one of the clamps is shown in the figure. The spring is required to drive the clamp upward while removing or inserting a work piece. A clamping force of 10 lbf is satisfactory. The base plate is 5/8 inch thick. The clamp screw has a 7/16 in-20 UNF thread. Allow 0.05 inch diametral clearance between screw and the inner coil...
Consider a cut thread bolt shown in Figure 8-17 of your textbook. The bolts are initially tightened by applying a torque to the nut to induce an initial axial preload for these fasteners. The clamped flanges of the steel housing each 1.25 inch thick. A 3/8-24 UNF SAE Grade 7 steel bolt is considered for this application. Bolt is 20% longer than the clamp length to allow sufficient protrusion for the nut. The external force on the bolted assembly is...
Please show solution for O step by step, use data and ansers
for N as given
(O)For the bolt of question (N) above, what is the required tightening torque? Answer Box: Torque 141 lb-in Total Clamping Force: F,-| 12,000 |lb Number of Bolts: N- Percentage of Proof Strength: PP- 75% SAE Grade 5 Steel Bolt Material Proof Strength of Bolt material: σ a 85,000 psi Lubrication Constant: K 0.15 Results Formula P FrIN Load on each Screw. P- 3000 b...
1. Bowling balls for regular 10-pin bowling are specified to have a diameter between 8.500 and 8.595 inches A sample of 25 balls has a mean diameter of 8.55 inches and a standard deviation of 0.023 inches Note: You have a sample standard deviation. (a) Construct a 99% confidence interval on the true mean diameter. (b) Construct a 95% confidence interval on the true mean diameter. 2. After a 9-game tournament, our intrepid bowler has recorded a striker percentage of...
A gear has been designed to have a diameter of 3 inches. The standard deviation of the process is 0.3 inch. A control chart is shown. Each chart has horizontal lines drawn at the mean, μ, μ 2o, and at μ 3G. Determine if the process shown is in control or out of control. Explain Is the process in control or out of control? Select all that apply A. Out of control, because a point lies more than three standard...
You have a long piece of 8-inch-wide metal that you plan to make into a gutter by bending up 3 inches on each side (see below). The first two steps are about always labeling your picture a) Please label the angle(s) below with a variable. (They're the same) [1 pt] Now label the sides of the blue triangle below in terms of the variable you used in part (a). You'll need to use trigonometry to do this. Of course, show...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago