I am trying to connect the circuit below on a breadboard. Its a 555 timer configured to generate a sawtooth wave. It is simulating on proteus but i can seem to get the breadboard connection right can u please help me with the connections on the breadboard?


We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
can anyone help with 3-7? or help me get started? im not sure
how to set them up. please and thank you
I. The Monostable timer (also called the one-shot, abbreviated OS) has 2. Explain the difference between a retriggerable OS and a non A stable state() os gaun until it times ut. 3. Calculate the duration of the pulse generated by a 535 timer circuit configured to operate as an OS. The external resistance used for the generating the...
please help me with the Question below. please explain to me how arduino connections with the breadboard can be used to measure a few basic parameters of water quality? i paragrah is okay for me in your answer.
If someone could please help me with running this exercise with
a physical breadboard circuit, it would help me greatly. I
unfortunately do not have the right equipment to perform practical
measurements right now.
Thank you all
1- Design an Instrumentation Amplifier that satisfies all of the following conditions a. Dual Buffered inputs b. A,| of 10 c. Bandwidth of at least 200 rad/sec d. Zero dc output voltage for zero dc input voltage Vin1 R1 R2 Vo R3 Vin2...
Make a 4 bit 2 to 1 multiplexer circuit and block diagram and
connect it to a Hexadecimal-adder-subtractor. Ok so this is what
I've done, I already designed what's inside the mux block but I do
not know if this is the correct way to set up the connections
because it justs looks like a 4 to 1 multiplexer, but I do not know
if it is the same thing. Can you help me finish it and explain if
it...
Comprehensive:(10 points) 1. What ports of niMyDAQ you can use to generate +2.5 Voltage DC supply? (2 points) Analog otAt Pops ?and 2 2. How to connect Voltmeter and Ammeter in the circuit to measure voltage and current? Please fill the letter 'V or'A" in the circle as V stand for Voltmeter and 'A' for Ammeter (2 points) Refer to the circuit below which Ammeter connected to R in parallel. What is the value of I in this case? (3...
I am trying to find out a
design containing NOR and OR or AND gate for the interface block
design. I have completed a design for when A = B, but I am having
difficulty designing A < B and B > A on the subtractor where
the boxes have question marks. Please help!
8.3* The circuit of 8.2, configured as a subtractor, can be used to compare two 4-bit numbers. Subtractor outputs C4 and (S3..S0) can be combined logically...
Can someone please help me with this question? I cant seem do get the right answer! An expression for the electric field that was produced by a spherically symmetric distribution is 2.47×103r2 [^(r)] N/C. A 28.0 cm diameter spherical surface shares its center with the spherical electric field. What is the flux through this spherical surface?
I am really need these solutions. Can your help me please?
this is a last part for my class final. I am really stuck at
it
Problem 1 If v(t) = 80 cos(200t) V and i(t) = 180 cos(200t + 75°) mA for some load, then calculate the instantaneous power and average power absorbed by the load Problem 2 Find the average power absorbed by the 102 resistor in the circuit below 492 -15.2 20/45°v 01v. 81. 59 109 {v....
I have a question about the "sonny's blues" story by JAMES
BALDWIN.. It is asking that how do you think the FORM of the story
expresses, embodies or reflects the story's CONTENT? What should i
write about it ? I can not think of anything. PLEASE HELP With this
question. I am going to post the question . The subject is ENGLISH.
I dont know if i am posting the question in the right place. but
please i do need...