A three-phase transformer bank is rated at 500 kVA and have a 34.5/12 kV voltage ratio. Find the following ratings of each individual transformer in the bank when the transformer is ∆-Y connected: high voltage, low voltage, turns ratio (a), and apparent power.
A three-phase transformer bank is rated at 500 kVA and have a 34.5/12 kV voltage ratio....
A 3 phase transformer bank is rated at 500 kVA and has a 34.5/11 kV voltage ratio. Find the following ratings of each individual transformer in the bank when the transformer is wye to Delta connected : High voltage, low voltage, turns ratio, and apparent power
2. In order to meet an emergency, three single-phase transformers rated 100 kVA (each), 13.2 kV/2.4 kV are connected in Y-∆ on a 3-phase, 20 kV line. a. What is the maximum load that can connected to the transformer bank? b. What is the outgoing line voltage?
A three-phase Yy0 connected transformer has a nominal rating of 250 kVA and a voltage ratio 15:0.4 kV. After conducting the short-circuit test, where the secondary winding is short-circuited, it is found that the primary series resistance is 0.08 pu and the primary series impedance magnitude is 0.1pu. The effect of the parallel branch in the transformer’s equivalent circuit may be neglected. Explain what information ‘Yy0’ gives about the transformer. Draw the per-phase equivalent circuit of the transformer during the...
Problem 2: A three-phase transformer bank (1-phase transformers) is to handle 30 MVA and have a primary voltage of 115kVLL and a secondary voltage of 4.16kVLL. Find the rating of each individual transformer in the bank (high side voltage, low side voltage, transformer turn ratio, and apparent power rating of each transformer) if the bank is connected: Wye-Wye Wye-Delta Delta-Wye Delta-Delta Draw winding connections for (a)-(d) (NOTE: This step does not need to be done in MATLAB). Assume all delta...
A three single-phase transformers steps up the three-phase generator voltage of 13.8 kV (line to line) to a transmission voltage of 138 kV (line to line). The generator rating is 41.5 MVA. Find the voltage, current, and kVA ratings of each transformer for the following connections: Low-voltage windings Delta, high-voltage windings Y. Low-voltage windings Y, high-voltage windings Delta.
A three-phase Y-A transformer is rated 225-kV:24-kV, 400 MVA and has a single-phase equivalent series reactance of 6.08 ? as referred to its high-voltage terminals. The transformer is supplying a load of 375 MVA at 0.89 power factor leading at a voltage of 24 kV (line to line) on its low-voltage side. It is supplied from a feeder whose impedance is 0.17 +/2.2 ? connected to its high-voltage terminals. For these conditions, calculate (a) the line-to-line voltage at the high-...
can you calculate this question and explain why?
thanks
1. A 250-kVA, 11000/2200-V, 50-Hz, single-phase transformer has the following parameters: RI 1.3 , R2 0.05 , Rel 193 k2, X1 4.5 Q X2 0.16 2 I,- 80 kQ Xml (a) Draw the approximate equivalent circuit of the transformer showing all the circuit parameters referred to the low-voltage side. Use the approximate equivalent circuit to calculate the input voltage and voltage regulation of the transformer when it delivers full load at...
A three phase power transformer of 100 (KVA), 22 / 12.7 (kV) and Δ-Y has a resistance of 0.15 (pu) and a reactance of 0.6 (pu). The elements of the excitation branch are R_m = 100 (pu) and X_m = 20 (pu) a) If this transformer supplies a load of 80 (KVA) with an FP = 0.8 delay, draw the phasor diagram of one phase of the transformer. b) What is the voltage regulation of the transformer bank in these...
A power transformer has rated power of 100 KVA and rated primary voltage of 22 KV. The series impedance is given as 1 + 15% pu. Find the series impedance in ohms.
Problem 3. A three-phase transformer is constructed using three single-phase two-winding trans- formers, each has the same ratings of 500 MVA, 15/240 kV, and leakage impedance of XT.p.u 0.2 p.u The high-voltage side of the three-phase transformer is connected to a three-phase Y-connected load that absorbs 1000 MVA at 0.9 power factor (lagging). The phase-a voltage across the load is Van 2402(0) kV. Answer the following questions. [10 points] a) Calculate the phase-a voltage at the low-voltage side (denoted by...