1.5 L of 19 ∘C water is placed in a refrigerator. The refrigerator's motor must supply an extra 7.0 W power to chill the water to 5∘C in 1.0h. What is the refrigerator's coefficient of performance?
1.5 L of 19 ∘C water is placed in a refrigerator. The refrigerator's motor must supply...
Constants I Periodic Table A refrigerator using helium gas operates on the reversed cycle shown in the following figure. Assume that T1 -18 °C and T2 =-78 °C(Figure 1) Figure く 1of1 p (kPa) Adiabats 150 V (cm) 0 20 40 60 80 100 What is the refrigerator's coefficient of performance? Express your answer using two significant figures. you need s hotrecoghized. Review a lis acceptable units. ANSWER 5: Deduction:-3% K 1.2 P 2000J Previous Answers ANSWER 6: Deduction:-3% Correct...
30 points / A taken from a 30 °C environment and laid out in a refrigerator at 5 °C. They have approximately the same physical properties as water, and the heat transfer coefficient inside the refrigerator is approximately 10 W/m2-K. You can neglect any thermal radiation. dozen approximately cylindrical cucumbers, 4 cm in diameter and 12 cm in length, are What will the temperature of the centers of the apples be after one hour? How much energy will the refrigerator...
l kg of water for a party, and only have 5 minutes to do it. Relying on nothing es, a dixicup, duct tape and a piece of string, you manage to build a refrigerator but your keen physical abiliti unit which can do the job. The temperature inside the refrigeration unit is 273 K, and the temperature outside is 350 K. Since you area brilliant UIUC student, assume that your refrigerator has the maximum possible efficiency. The Latent Heat o...
Questions Apitcher containing 0.87 L of water at 4°C is removed from the refrigerator How many tenere needed to wam the onemperature of 217 24.104.334 : Do 1.00 Moving to other question will save this response NON Polar р $ Y T ااااال R E H G w M IN
A 480-V 100-kW 0.85-PF leading 50-Hz six-pole Y-connected synchronous motor has a synchronous reactance of 1.5 and a negligible armature resistance. The rotational losses are also to be ignored. This motor is to be operated over a continuous range of speeds from 300 to 1000 r/min, where the speed changes are to be accomplished by controlling the system frequency with a solid-state drive. (a) Over what range must the input frequency be varied to provide this speed control range? 6-6....
A water tower is fed from an underground water source (Figure 2). The difference in level is 67 m. The flow of water must be at least 55 m'/h. To provide this flow (55m/h), a pump must be driven at a speed of 690 RPM. It can turn faster, but without exceeding 900 RPM. Its efficiency is 81%. The pump is driven directly, therefore without gearbox, by an asynchronous motor, which itselif is supplied directly by the 400V/50 Hz three-phase...
A blacksmith drops 1.5 kg piece of iron heated to 525°C into 2 L of water with temperature of 70°C. What will be the final temperature of water? Calculate amount of evaporated water, and final temperature.
2. (5 points) A 35 g ice cube at 0 °C is placed on a 1.5 kg Al plate initially at 40 °C? What will be the final temperature once the ice melts and the plate and water come to equilibrium? Assume that no heat is exchanged with the environment. Use 333 kJ/kg for the heat of fusion for water, 4.186 kJ/(kg °C) for the specific heat of water, and 0.900 kJ/(kg oC) for the specific heat of Al
Name HW Due 530/19 ART 430, 440 1. The motor disconnecting means is not required to be in sight from the motor and the driven machinery location, provided_ (a) the (b) the provisions for locking are permanently installed on, or at, the switch or circuit breaker used as the controller disconnecting means (c) locating the motor disconnecting means within sight of the motor is impractical or introduces additional or increased hazards to people or property (d) all of these controller...
earning Goal: To understand that a heat engine run backward is a heat pump that can be used as a refrigerator. By now you should be familiar with heat engines--devices, theoretical or actual, designed to convert heat into work. You should understand the following: Heat engines must be cyclical; that is, they must return to their original state some time after having absorbed some heat and done some work). Heat engines cannot convert heat into work without generating some waste...