Show that the maximum power for a PM brush DC motor is obtained when the motor is operating at a speed equal to half the no-load speed.
Show that the maximum power for a PM brush DC motor is obtained when the motor...
5. Explain the condition for a DC motor to develop the maximum power. If a DC machine having an armature resistance of 0.5Ω and the full load current of 20 A. Find the induced emf of machine when it acts as: (i) Motor and (ii) Generator
If a manufacturer's specifications for a PM DC motor are as follows, what are the motor's no-load speed, stall current, starting torque, and maximum power for an applied voltage of 10 V? ■ Torque constant 0.12 Nm/A Electrical constant 12 V/1000 RPM Armature resistance-: 1.5 Ω
need the answer for the question no. 1 ENGR 113 Homework DC Motor Objectives Plot the Torque-Speed curve for a given DC motor given the stall torque and no load speed values Calculate the rotational power for a DC motor given the stall torque and no load speed values Plot the rotational power on a Torque-Speed curve to see the relationship between torque, speed, and power Calculate the maximum efficiency of a DC motor. Calculate the operating point for a...
A DC motor, when supplied from a 211 V power supply is observed to rotate under no-load conditions at 1,700 rpm. A stall test shows that the winding resistance is 1.65 ? The motor is connected to a load whose torque-speed characteristic is given by ? = ?×0.178. Find the speed (in rpm) at which the motor will drive this load. rpm (Give your answer in rpm to 3 s.f.)
Q1b) DC Machines [ 6 marks ] You are given a 24 V DC motor. When you connect it to a 24 V supply, under no-load conditions it spins at 2,000 rpm. With the same 24 V supply, when the motor is stalled, the input current is 50 A. i) Calculate the back-emf constant and hence the stall torque of the motor. Find also the armature resistance. [3 marks ] ii) The DC motor has a rated input current of...
A 6 hp, 180 V shunt dc motor draws a full-load current of 30 A from the power supply. The motor has a field (shunt) resistance of 150 Ω. The armature resistance of the motor is 0.1 Ω. When the motor speed is 1800 rpm (this is not the full-load speed), the relationship between the induced voltage
The power input to a dc shunt motor during rated-load conditions is 100 W. The rotor speed is 2000 r/min, and the armature voltage is 100 V. The armature resistance is 2? and Rf = 200 ?. Calculate the no-load rotor speed. 2. The power input to a dc shunt motor during rated-load conditions is 100W. The rotor speed is 2000r/min, and the armature voltage is 100V. The armature resis- tance is 2 Ω and Rf-200Ω. Calculate the no-load rotor...
The armature windings of a dc motor have a resistance of 8.0 Ω . The motor is connected to a 120-V line, and when the motor reaches full speed against its normal load, the back emf is 108 V. The load is increased so it causes the motor to run at half speed. What will be the current in the motor in this case? (Express your answer to two significant figures and include the appropriate units.)
Problem 1: Speed versus time plot of a small DC motor is obtained when 1 Volt input is applied. The response curve is shown below: a) Approximate the open loop transfer 6 function, G(s) of the DC motor. b) A simple proportional controller (P- controller) is applied to the same DC motor. The control goal is to track a constant target speed ofr 150 rpm. Determine the control gain Kp which guarantees an offset error of e 5 rpm. (i.e.,...
FQ3 3. A 240 V DC series motor with 0.1 ohm armature resistance and 0.1 ohm field resistance runs at 1200 rpm and 100 Amp. of full load speed and armature current respectively. The motor has a brush contact drop of 2 volts. Find the motor full load torque and efficiency If the motor is to drive a pump that requires a torque of 150 NM, find the speed as the motor drives the given pump. a. b.