when calculating the power of a pure resistive load the voltage and current are in phase...

Question

Question

when calculating the power of a pure resistive load the voltage and current are in phase with each other and the power factor is

engineering Electrical-Engineering

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

25. When calculating the power of a pure resistive load, the voltage and current are in...

25. When calculating the power of a pure resistive load, the voltage and current are in power factor is a. one b. two c. three d. four Bonus Question: Find missing values for: Ip. Np, Is, Ratio (2pts each) Kauu Ep 120 V Es 500 V Copyright Coppeling Ns 800 Turns pyright Cengage Learning. Powered by Cognero.
If a three-phase load is a pure reactive load, then the power calculated has units of...

If a three-phase load is a pure reactive load, then the power calculated has units of _____. A delta-connected three-phase alternator is driving a wye-connected resistive load. The alternator output voltage is 480 V. The load resistors are 12 W each. What is the phase current in the alternator?
A voltage of 220V (rms) line to line voltage is applied across a three phase Y...

A voltage of 220V (rms) line to line voltage is applied across a three phase Y connected resistive load. Each phase of the Y, connected loads has a resistance of 127Ω. i) Find current through each phase i) Find the total three phase power ii) Find the power factor of the load

Explain the loading characteristics of a three-phase alternator in capacitive, resistive and inductive. Please indicate the...

Explain the loading characteristics of a three-phase alternator in capacitive, resistive and inductive. Please indicate the voltage, current and power relationship in each load condition. Lastly, also explain the power factor relationship. Answer in paragraph form or bullet form. Thanks
In a transformer load test (Resistive and at a unity power factor), what should be the...

In a transformer load test (Resistive and at a unity power factor), what should be the expected voltage regulation and primary power factor?
Q1. Design a three-phase balanced power system where the load is connected with the power supply...

Q1. Design a three-phase balanced power system where the load is connected with the power supply through a resistive transmission line. Your design needs to meet the following criteria: 1. Phase sequence for the power supply is ACB. You can take any phase or line as reference. 2. For the power supply, the line and phase voltages are related by a factor of V3. Please do not ignore the phase shift between the line and phase voltage or current. 3....

4) Calculate load voltage, phase, load current, phase and load power for the tables below. (fill ...

4) Calculate load voltage, phase, load current, phase and load power for the tables below. (fill the tables for figure4 circuit) For table 1, use calculated maximum power CL and for table2 use calculated maximum power RL VoadPhaseVload lload (mA) RL PL (mW) 100Ω 3900 560Ω 8200 1000Ω 12000 1800Ω 3300Ω 1 0000Ω Table 1: Load Power with respect to RL (use maximum power CL for this table) LoadPower PL (mW) CL Vload (V)PhaseVload() Iload (mA) Phaselload() 1 nF 3.3...
In a transformer load test (Resistive and at a unity power factor), what should be the...

In a transformer load test (Resistive and at a unity power factor), what should be the relationship of the primary power to the secondary load power and what should be the relationship of the primary current to the secondary current.
Derive the expressions of the average and rms values of the load voltage and current in...

Derive the expressions of the average and rms values of the load voltage and current in three-phase uncontrolled bridge rectifiers with resistive load. Draw the waveforms of supply voltage (line-line voltages), transformer phase current (only one phase), load voltage, load current and diode current.

A three-phase load has a voltage of 1.0 pu with current 0.1 pu. The current lags...

A three-phase load has a voltage of 1.0 pu with current 0.1 pu. The current lags the voltage by 30 degrees. A lossless capacitor is to be installed in parallel with the load to improve the overall power factor to 0.95 lagging. Find the amount of reactive power that needs to be injected by the capacitor. Select one: a. 0.0646 pu b. 0.0215 pu C. 0.0785 pu d. -0.0215 pu