If a force of 500 N on a tightening wrench produces a torque of 700 N.m...

Question

Question

If a force of 500 N on a tightening wrench produces a torque of 700 N.m on a bolt. Calculate length of the wrench in m.

engineering Mechanical-Engineering

Answer 1

Answer #1

Please dear thumpsup for the work. Thank you.

Answer 2

Similar Homework Help Questions

When tightening a bolt, you push perpendicularly on a wrench with a force of 160 N at a distance of 0.155 m from the center of the bolt.

When tightening a bolt, you push perpendicularly on a wrench with a force of 160 N at a distance of 0.155 m from the center of the bolt. Part(a) How much torque are you exerting on the wrench, in newton meters, relative to the center of the bolt?
The bolts on the cylinder head of an engine require tightening to a torque of 85...

The bolts on the cylinder head of an engine require tightening to a torque of 85 m⋅N If a wrench is 28 cm long, what force perpendicular to the wrench must the mechanic exert at its end? If the six-sided bolt head is 15 mm in diameter, estimate the force applied near each of the six points by a socket wrench.
The bolts on the cylinder head of an engine require tightening to a torque of 79m?N...

The bolts on the cylinder head of an engine require tightening to a torque of 79m?N . If the six-sided bolt head is 15 mm in diameter, estimate the force applied near each of the six points by a socket wrench.

A car tune-up manual calls for tightening the spark plugs to a torque of 37.0 N⋅m...

A car tune-up manual calls for tightening the spark plugs to a torque of 37.0 N⋅m . To achieve this torque, with what force must you pull on the end of a 20.5 cm -long wrench if you pull (a) at right angles to the wrench shaft and (b) at 106 ∘ to the wrench shaft?
1. Suppose a torque T is generated by applying a force F to a wrench. The...

1. Suppose a torque T is generated by applying a force F to a wrench. The force is applied some distance L from the bolt that the wrench is tightening. If the force applied is reduced to a quarter of the original force, and the new torque generated is 3T, at what distance from the bolt is this new force applied? 2. Two extended bodies, object 1 and object 2, are left to roll down an incline from an initial...
4. A force of 285 N is exerted on the end of a wrench in order...

4. A force of 285 N is exerted on the end of a wrench in order to apply a torque of 48.9 N m to a bolt head. The point of application of the force is 21.5 cm from the center of the bolt. What angle does the force make with respect to the wrench handle? degrees

a. If the applied force N=5kN, determine the torque at cross section C in N.m b....

a. If the applied force N=5kN, determine the torque at cross section C in N.m b. The pipe shown has a inner diameter of 50 mm and an outer diameter of 71mm. if its tightened against the support at A using a torque wrench at B by applying a force N =102N instead of 5kN, determine theax shear stress in kPa developed In the material at the cross section C when the forces shown in the figure below are applied...
A force of 295 N is exerted on the end of a wrench in order to...

A force of 295 N is exerted on the end of a wrench in order to apply a torque of 48.4 N·m to a bolt head. The point of application of the force is 21.5 cm from the center of the bolt. What angle does the force make with respect to the wrench handle?
A force of 289 N is exerted on the end of a wrench in order to...

A force of 289 N is exerted on the end of a wrench in order to apply a torque of 35.9 NÂ·m to a bolt head. The point of application of the force is 21.5 cm from the center of the bolt. What angle does the force make with respect to the wrench handle?