AC sweep
Q1: What is the attenuation in dB for the RC filter at 100k Hz?
Q2: What is the phase at 100 Hz? (Read on your plot)
Homework Answers
Add Answer to:
AC sweep
Q1: What is the attenuation in dB for the RC filter at 100k
Hz?...
AC sweep Q3: What is the attenuation in dB for the RL filter at 100k Hz?...
AC sweep
Q3: What is the attenuation in dB for the RL filter at 100k
Hz?
Q4: What is the phase at 100 Hz? (Read on your plot)
PR1 R1 1 V 1k2 2 V1 L1 17 1kHz 0 0° 100μΗ 4
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the f...
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the filtered analog signal at 50, 75 and 200 Hz. (use k -1) o Determine the order of the filter if magnitude ratio of <0.01 is needed at 200 Hz.
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a...
Q1: What is the total impedance of the circuit? Q2: At what AC source frequency the...
Q1: What is the total impedance of the circuit?
Q2: At what AC source frequency the voltage and the current in
the circuit are in phase?
C1 PR1 3 N HE 50.0F C2 HE 100nF PR4 V1 30.0V 10.0kHz 0" R1 10KO LT BOOMH R2 ΘΩ PR3 PR2 4 191.736A
2. If the voltage gain of the amplifier is m (50 points) easured to be 50 dB, what is the value of Ru? R8 4.7 Ω C5 R6 R3 4.7kQ c3 R1 Q2 20pF 2N2222A 20pF C1 Q1 2N2222A V1 15V RL R9 1200 R4 V...
2. If the voltage gain of the amplifier is m (50 points) easured to be 50 dB, what is the value of Ru? R8 4.7 Ω C5 R6 R3 4.7kQ c3 R1 Q2 20pF 2N2222A 20pF C1 Q1 2N2222A V1 15V RL R9 1200 R4 V2 5mVpk R2 0° 120Ω R7 1kHz 22ka C4 R5 C2 3300.3 100 F 300 100uF
2. If the voltage gain of the amplifier is m (50 points) easured to be 50 dB, what is...
are those right and what about the others? S. AC Analysis: Determine all values requested below,...
are those right and what about the others?
S. AC Analysis: Determine all values requested below, Make sure al work s Rin Base Rin total Attenuation Rc 2.92s Output voltage Use the circuit below to answer problems 7-9. 12Vdc RC 1.8k R1 C2 01 C1 RL 100k 100 1uF R2 11k VS RE1 600 toched if it isn't shown below
please I need details l and....Debate Club | Offic A) Theoretical Design Design a common emitter BJT amplifier with the following requirements: -Rin-10 K2, and Ro-45 ㏀ (Neglect the Early voltage...
please I need details
l and....Debate Club | Offic A) Theoretical Design Design a common emitter BJT amplifier with the following requirements: -Rin-10 K2, and Ro-45 ㏀ (Neglect the Early voltage Effect) Vo/Vsig- Gv-40 VIV or 32 dB " VCC-9 V V, IC-1mA, VCE-3.25V and β-100 RL-40 kQ, Rsige I ka, R 1-3R2, and C1-C2-1 μF Voc RC C2 R1 Rsig C1 RL R2 RE B) Verify your design using Orcad Capture Pspice by doing 1) AC sweep (frequency response):...
Need to create a bandpass filter with cutoff frequencies from 300Hz to 3000Hz with a op-amp included in circuit. I have...
Need to create a bandpass filter with cutoff frequencies from
300Hz to 3000Hz with a op-amp included in circuit. I have examples
below. you can use multisim, Pspice, or matlab for simulation of
circuit. I will up vote. Thanks.
Band-Pass Jitte L 300 H2 2R Ra C ХВР1 C1 IN OUT R2 53.10 1pF V1 R1 5310 6Vpk 1KHZ 0° BODE PLOT BODE PLOT m Design 000 50 00 -N00 00 - 150 00 Cune -20000 Bode Reault 100G 100...
Series and parallel RL and RC circuits with an AC source. A 60 Hz voltage source...
Series and parallel RL and RC circuits with an AC source. A 60 Hz voltage source has an amplitude of VT-120 V. For the following problems, compute the indicated phasors including both magnitudes and phase angles, and sketch the phasor diagrams (no submission) Q1. The source is connected across a series RL ac circuit with R 7.8 Ohm and XL = ωし= 5.1 Ohm. 1a) Find the magnitude of impedance of the series combination (Unit: Ohm) Submit Answer Tries 0/3...
HW11F19.pdf Download Q1 (10pts.): Extract an estimation of the transfer function that was used to create the Bode plot shown below IK- v(3) 20° 8dB 0d -8d 16d 24d -32dB -40d 48d -56dB -64d 72dB -80dB...
HW11F19.pdf Download Q1 (10pts.): Extract an estimation of the transfer function that was used to create the Bode plot shown below IK- v(3) 20° 8dB 0d -8d 16d 24d -32dB -40d 48d -56dB -64d 72dB -80dB -20° -40° -60° -80° 100° 120 140° 160° ト·H 111翔 1-2 200° 100Hz 1MHz 10KHz 100KHz 1KHz 1. What kind of filter is it? 2. What order is the filter? 3. What is the DC, AC, or Midband Gain (not in dB)? 4. What...
I need help to measure the high frequency cutoff. The circuit below is for HIGH PASS...
I need help to measure the high frequency cutoff. The circuit
below is for HIGH PASS FILTER
I made it but I dont know how to accurately measure the high
cutoff as what we did in the lab. in the lab we get 14.35
kHz but when I try in the multisim and varing the freqency
as shown in the table below I dont get any change.
Please do it in multisim and explain your answer, thanks.
f
1-kHz
2-kHz...
AC sweep
Q3: What is the attenuation in dB for the RL filter at 100k
Hz?
Q4: What is the phase at 100 Hz? (Read on your plot)
PR1 R1 1 V 1k2 2 V1 L1 17 1kHz 0 0° 100μΗ 4
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the filtered analog signal at 50, 75 and 200 Hz. (use k -1) o Determine the order of the filter if magnitude ratio of <0.01 is needed at 200 Hz.
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a...
Q1: What is the total impedance of the circuit?
Q2: At what AC source frequency the voltage and the current in
the circuit are in phase?
C1 PR1 3 N HE 50.0F C2 HE 100nF PR4 V1 30.0V 10.0kHz 0" R1 10KO LT BOOMH R2 ΘΩ PR3 PR2 4 191.736A
2. If the voltage gain of the amplifier is m (50 points) easured to be 50 dB, what is the value of Ru? R8 4.7 Ω C5 R6 R3 4.7kQ c3 R1 Q2 20pF 2N2222A 20pF C1 Q1 2N2222A V1 15V RL R9 1200 R4 V2 5mVpk R2 0° 120Ω R7 1kHz 22ka C4 R5 C2 3300.3 100 F 300 100uF
2. If the voltage gain of the amplifier is m (50 points) easured to be 50 dB, what is...
are those right and what about the others?
S. AC Analysis: Determine all values requested below, Make sure al work s Rin Base Rin total Attenuation Rc 2.92s Output voltage Use the circuit below to answer problems 7-9. 12Vdc RC 1.8k R1 C2 01 C1 RL 100k 100 1uF R2 11k VS RE1 600 toched if it isn't shown below
please I need details
l and....Debate Club | Offic A) Theoretical Design Design a common emitter BJT amplifier with the following requirements: -Rin-10 K2, and Ro-45 ㏀ (Neglect the Early voltage Effect) Vo/Vsig- Gv-40 VIV or 32 dB " VCC-9 V V, IC-1mA, VCE-3.25V and β-100 RL-40 kQ, Rsige I ka, R 1-3R2, and C1-C2-1 μF Voc RC C2 R1 Rsig C1 RL R2 RE B) Verify your design using Orcad Capture Pspice by doing 1) AC sweep (frequency response):...
Need to create a bandpass filter with cutoff frequencies from
300Hz to 3000Hz with a op-amp included in circuit. I have examples
below. you can use multisim, Pspice, or matlab for simulation of
circuit. I will up vote. Thanks.
Band-Pass Jitte L 300 H2 2R Ra C ХВР1 C1 IN OUT R2 53.10 1pF V1 R1 5310 6Vpk 1KHZ 0° BODE PLOT BODE PLOT m Design 000 50 00 -N00 00 - 150 00 Cune -20000 Bode Reault 100G 100...
Series and parallel RL and RC circuits with an AC source. A 60 Hz voltage source has an amplitude of VT-120 V. For the following problems, compute the indicated phasors including both magnitudes and phase angles, and sketch the phasor diagrams (no submission) Q1. The source is connected across a series RL ac circuit with R 7.8 Ohm and XL = ωし= 5.1 Ohm. 1a) Find the magnitude of impedance of the series combination (Unit: Ohm) Submit Answer Tries 0/3...
HW11F19.pdf Download Q1 (10pts.): Extract an estimation of the transfer function that was used to create the Bode plot shown below IK- v(3) 20° 8dB 0d -8d 16d 24d -32dB -40d 48d -56dB -64d 72dB -80dB -20° -40° -60° -80° 100° 120 140° 160° ト·H 111翔 1-2 200° 100Hz 1MHz 10KHz 100KHz 1KHz 1. What kind of filter is it? 2. What order is the filter? 3. What is the DC, AC, or Midband Gain (not in dB)? 4. What...
I need help to measure the high frequency cutoff. The circuit
below is for HIGH PASS FILTER
I made it but I dont know how to accurately measure the high
cutoff as what we did in the lab. in the lab we get 14.35
kHz but when I try in the multisim and varing the freqency
as shown in the table below I dont get any change.
Please do it in multisim and explain your answer, thanks.
f
1-kHz
2-kHz...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 11 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 11 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 11 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 11 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 11 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 11 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 11 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 11 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 11 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 11 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 11 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 11 months ago