Homework Answers
Add Answer to:
i need the answers to these two problems
HOLE D HOLE G PITCH PITCH cel- HOLE...
i need the answers to theses two problems W1210 D=0.750 H 22. A 60 degree slot...
i need the answers to theses two problems
W1210 D=0.750 H 22. A 60 degree slot has been machined in a fixture. The slot is checked by placing a pin in the slot and indicating the distance between the top of the fixture and the top of the pin as shown in the accompanying figure. Compute distance H to three decimal places by using the formula: H= 1.5x D-0.866 x W. All dimensions are in inches. a. 0.069 in b....
i need the answer to the 2 problems 14 HOLES EQUALLY SPACED |--8 0-0-0-0-0-0-0-0-0-0-0 -5 FEET...
i need the answer to the 2 problems
14 HOLES EQUALLY SPACED |--8 0-0-0-0-0-0-0-0-0-0-0 -5 FEET FIGURE 36-1 29. Holes are to be drilled in the length of angle iron as shown in the accompanying figure 36-1. What is the distance in inches between two consecutive holes? a 3 1/4 b. 3 1/2 c. 3 3/4 d. 4 staroxys- FIGURE 37-9 30. In the accompanying figure 37-9. what is the length from A to B? a. 2x + 7 b....
interpreting engineering drawing. I dont need answer 1 port casting bus 12 What is the height...
interpreting engineering drawing. I dont need answer 1
port casting bus 12 What is the height of the shaft support cas machining? QUESTIONS: 1. Calculate distances to 2. How many surfaces require finishing? 3. What tolerance is permitted on dimensions which do not specify a certain tolerance? 4. What type of section view is used on part 17 5. What type of section view is used on part 27 The site of the two holes are to be changed comodate...
82.6 642 6.40 - 57 5.4 R0.8 MAX 28.6 035 28.4 #51 3 45 ф100 R3 #8.5 M10 X 1.5-6H 45 4X 10.5 NOTE:...
82.6 642 6.40 - 57 5.4 R0.8 MAX 28.6 035 28.4 #51 3 45 ф100 R3 #8.5 M10 X 1.5-6H 45 4X 10.5 NOTE: ALL DIMS IN mm ーAX 90. GRAY IRON FIN. DIMS i02 UNFİN, DIMS 최 ANGLE ±0° 30' FLANGED HUB 31A059 2 Refer to drawing 31A059 to answer the following questions. the units of measurement in (a) inches, (b) millimeters, or (c) centimeters? 2. Is the section view a (a) half-section or a (b) full section? what...
i need the answeres to all three of the problem. 13. Bronze is an alloy of...
i need the answeres to all three of the problem.
13. Bronze is an alloy of copper, zinc, and tin with small amounts of other elements. If the percent composition is 56% copper, 1% zinc, and 42% tin, what is the ratio of copper to tin? a. 4/3 b. 3/2 c. 2/1 d. 3/1 14. The total amount of stock milled off an aluminum casting in two cuts is 6.18 millimeters. The roughing cut is 2.30 millimeters greater than the...
i need the answers to all four of the problems. 1. A slot is milled the...
i need the answers to all four of the problems.
1. A slot is milled the full length of a steel plate that is 4 12 feet long. This operation takes a total of 2 1/8 minutes. How many feet of steel are cut in one minute? a. 1 15/16 6.2 2/17 c. 2 7/19 d. 3 2. A tube has an inside diameter of 1/2 inch and a wall thickness if 1/16 inch. The tube is to be filled...
T. 0.875 inch, find W. side diameter of the bearing? Or- dowolto pscort on sanwa BELOON...
T. 0.875 inch, find W. side diameter of the bearing? Or- dowolto pscort on sanwa BELOON zo snblov 008-09 0.632 June ronto 3.202 1999 loco odbi 0.212 120 1919 14. If A = 0.375 inch, B = 0.923 inch, and C= 1.0992 inches, find G. 15. If x = 0.9375 inch and Y= 16.) The inside diameter of a motor shaft bearing is 0.0075 centimeter wider than the shaft. The shaft diameter is 4.75 centimeters. What is the in- 28...
I NEED SOLUTION TO PART#8 The two objects as pictured make a completely elastic collision. (Problems...
I NEED SOLUTION TO PART#8
The two objects as pictured make a completely elastic collision. (Problems 1,2) 1. What is the change in energy for the object that was initially at rest (in terms of vo, m, theta)? 2. What is the angle theta (in terms of m and vo)? The object as shown slides up the ramp, which is free to roll on á frictionless surface. (Problems 3-5) 3. What is vf for the two objects (in terms of...
I need A through G DOOOOLLELLDE DEO DOPO DODUO DO (13%) Problem 12: Two parallel plates...
I need A through G
DOOOOLLELLDE DEO DOPO DODUO DO (13%) Problem 12: Two parallel plates are charged with + and respectively as shown in the figure, where Q = 31 nC. The area of each plate is A = 0.021 m². The distance between them is d= 9.6 cm. The plates are in the air. Otheexpertta.co A 14% Part (a) With the information given, write the equation of the capacitance in terms of €0, A, d. Grade Summary Deductions...
looking for question 3 a,b,c,d,e,f,g,h and i. Thank you it's the same question with different situations....
looking for question 3 a,b,c,d,e,f,g,h and i. Thank you
it's the same question with different situations.
3. Now let's use trial-and-error to see if we can figure out the inheritance pattern of this trait. For EVERY pedigree diagram below and on the following pages, label what you know about the genotype of each individual shown from the information provided in the pedigree and the assumption specified above each one. You MUST label ALL FOUR diagrams separately! Genotypes in these pedigrees...
i need the answers to theses two problems
W1210 D=0.750 H 22. A 60 degree slot has been machined in a fixture. The slot is checked by placing a pin in the slot and indicating the distance between the top of the fixture and the top of the pin as shown in the accompanying figure. Compute distance H to three decimal places by using the formula: H= 1.5x D-0.866 x W. All dimensions are in inches. a. 0.069 in b....
i need the answer to the 2 problems
14 HOLES EQUALLY SPACED |--8 0-0-0-0-0-0-0-0-0-0-0 -5 FEET FIGURE 36-1 29. Holes are to be drilled in the length of angle iron as shown in the accompanying figure 36-1. What is the distance in inches between two consecutive holes? a 3 1/4 b. 3 1/2 c. 3 3/4 d. 4 staroxys- FIGURE 37-9 30. In the accompanying figure 37-9. what is the length from A to B? a. 2x + 7 b....
interpreting engineering drawing. I dont need answer 1
port casting bus 12 What is the height of the shaft support cas machining? QUESTIONS: 1. Calculate distances to 2. How many surfaces require finishing? 3. What tolerance is permitted on dimensions which do not specify a certain tolerance? 4. What type of section view is used on part 17 5. What type of section view is used on part 27 The site of the two holes are to be changed comodate...
82.6 642 6.40 - 57 5.4 R0.8 MAX 28.6 035 28.4 #51 3 45 ф100 R3 #8.5 M10 X 1.5-6H 45 4X 10.5 NOTE: ALL DIMS IN mm ーAX 90. GRAY IRON FIN. DIMS i02 UNFİN, DIMS 최 ANGLE ±0° 30' FLANGED HUB 31A059 2 Refer to drawing 31A059 to answer the following questions. the units of measurement in (a) inches, (b) millimeters, or (c) centimeters? 2. Is the section view a (a) half-section or a (b) full section? what...
i need the answeres to all three of the problem.
13. Bronze is an alloy of copper, zinc, and tin with small amounts of other elements. If the percent composition is 56% copper, 1% zinc, and 42% tin, what is the ratio of copper to tin? a. 4/3 b. 3/2 c. 2/1 d. 3/1 14. The total amount of stock milled off an aluminum casting in two cuts is 6.18 millimeters. The roughing cut is 2.30 millimeters greater than the...
i need the answers to all four of the problems.
1. A slot is milled the full length of a steel plate that is 4 12 feet long. This operation takes a total of 2 1/8 minutes. How many feet of steel are cut in one minute? a. 1 15/16 6.2 2/17 c. 2 7/19 d. 3 2. A tube has an inside diameter of 1/2 inch and a wall thickness if 1/16 inch. The tube is to be filled...
T. 0.875 inch, find W. side diameter of the bearing? Or- dowolto pscort on sanwa BELOON zo snblov 008-09 0.632 June ronto 3.202 1999 loco odbi 0.212 120 1919 14. If A = 0.375 inch, B = 0.923 inch, and C= 1.0992 inches, find G. 15. If x = 0.9375 inch and Y= 16.) The inside diameter of a motor shaft bearing is 0.0075 centimeter wider than the shaft. The shaft diameter is 4.75 centimeters. What is the in- 28...
I NEED SOLUTION TO PART#8
The two objects as pictured make a completely elastic collision. (Problems 1,2) 1. What is the change in energy for the object that was initially at rest (in terms of vo, m, theta)? 2. What is the angle theta (in terms of m and vo)? The object as shown slides up the ramp, which is free to roll on á frictionless surface. (Problems 3-5) 3. What is vf for the two objects (in terms of...
I need A through G
DOOOOLLELLDE DEO DOPO DODUO DO (13%) Problem 12: Two parallel plates are charged with + and respectively as shown in the figure, where Q = 31 nC. The area of each plate is A = 0.021 m². The distance between them is d= 9.6 cm. The plates are in the air. Otheexpertta.co A 14% Part (a) With the information given, write the equation of the capacitance in terms of €0, A, d. Grade Summary Deductions...
looking for question 3 a,b,c,d,e,f,g,h and i. Thank you
it's the same question with different situations.
3. Now let's use trial-and-error to see if we can figure out the inheritance pattern of this trait. For EVERY pedigree diagram below and on the following pages, label what you know about the genotype of each individual shown from the information provided in the pedigree and the assumption specified above each one. You MUST label ALL FOUR diagrams separately! Genotypes in these pedigrees...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago