By applying a base current of 50μA to the transistor of the figure and a voltage...

Question

Question

By applying a base current of 50μA to the transistor of the figure and a voltage of 5V through Rc.
Calculate the βcd of the transistor

Rς ξι.0 ΕΩ RB Vec 100 ΚΩ BB +

engineering Electrical-Engineering

Answer 1

Answer #1

Reloka + Given Ip=50MA. VRca svi Vic RR M look I care Re - SA 5 Ik Fe=5mA we know that Ica Boche Boca 5m Sou I Boca =100

Answer 2

Similar Homework Help Questions

An NPN Transistor has a DC base bias voltage, Vb of 10.8v and an input base...

An NPN Transistor has a DC base bias voltage, Vb of 10.8v and an input base resistor, Rb of 80kΩ. What will be the value of the base current (in μA) into the transistor?
1) Calculate the value of the base current IB. (in μA) 2) Calculate the value of...

1) Calculate the value of the base current IB. (in μA) 2) Calculate the value of the base collector current IC. (In mA) 3) Calculate the value of the collector-emitter voltage VCE. (In V) Required information In the circuit below: RB = 820 kN, Vcc = 12 V, RC = 3 kN2, and Bdc = 100. Note: The transistor is silicon. Vcc w Rc Re Bdc
1. For the transistor circuit shown in figure 1, what is: a. Vce when VIN =...

1. For the transistor circuit shown in figure 1, what is: a. Vce when VIN = OV? b. What minimum value of IB is required to saturate the transistor if Boc is 200? c. Calculate the maximum value of Rs when Vin = 5V. VCC 10V RC 1.0 K RB Q1 VIN=0V 15C02MH-TLE GND Figure

*5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an in...

*5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an initial peak base current, IB,-8 1B2, where 1B2 denotes the minimum base current required to drive the transistor to saturation. Assume a collector load resistance, Rc-8 Ω, collector supply voltage Vs = 30 V, large signal current of the transistor, hFE-min. 10, max. 20), VBE(on)-0.8 V, and the input is periodic pulse waveform (0 to 6) V, with a duty cycle, D-0.5. Also,...
Find IC and VEC for the pnp transistor circuit in Figure 5–15. EE +10 V R,...

Find IC and VEC for the pnp transistor circuit in Figure 5–15. EE +10 V R, 10 kΩ RE 1.0 kΩ 4) βpc = 150 Rc 8 RI 22 ΚΩ 2.2 kΩ FIGURE 5-15
1) Plot base current of a npn transistor versus base-emitter voltage 2) Plot Gate current of...

1) Plot base current of a npn transistor versus base-emitter voltage 2) Plot Gate current of a MOSFET transistor versus gate-source voltage

ECE 3424 Student Name & ID: An npn transistor having 1s = 10-"A and B =...

ECE 3424 Student Name & ID: An npn transistor having 1s = 10-"A and B = 100 is connected as follows: The emitter is grounded, the base is fed with a constant-current source supplying a dc current of 10 u A, and the collector is connected to a 5-V dc supply via a resistance Rc of 3 k12. Assuming that the transistor is operating in the active mode, find VBE and Vce. Use these values to verify active-mode operation. Replace...
Figure 3 Transistor amplifire circuit with source Vs and load R b) For the BJT switching...

Figure 3 Transistor amplifire circuit with source Vs and load R b) For the BJT switching circuit shown in Figure 4, i) Calculate the value of Ra so that the transistor is operating in saturation when switched on if the value of Rc is 3.9 kn. ii) What will the output voltage be for the applied input signal voltage shown if Vcet IS 0.2V? 5 V Re o V 5 V B 100 OV Figure 4 BUT switching circuit with...
Q.2. (a) Determine the region of operation for the following transistor when B = 100 and...

Q.2. (a) Determine the region of operation for the following transistor when B = 100 and Ves = 0.7 V. Also find I and V. (10) I + 5 V -15 V 1K 1K V 0 (b) For the circuit shown below, let B = 100 and VBE = 0.7 V. (a) Find VTH and RTH for the base circuit. (b) Determine Ice and VcEO + 5V +15V 500 ΚΩ 50 ΚΩ + 3V 500 ΚΩ 70 ΚΩ 5 ΚΩ...

*5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with...

*5. Design a BJT transistor drive circuit like the one shown Figure 10-7 (Hart's text) with an initial peak base current, IB,-8 1B2, where 1B2 denotes the minimum base current required to drive the transistor to saturation. Assume a collector load resistance, Rc-8 Ω, collector supply voltage Vs = 30 V, large signal current of the transistor, hFE-min. 10, max. 20), VBE(on)-0.8 V, and the input is periodic pulse waveform (0 to 6) V, with a duty cycle, D-0.5. Also,...