
A crankshaft screwdriver is used to tighten a screw at point A. Knowing that the forces indicated equivalent to a force-torque system applied in A with: ?⃗ = - 30 ? + ?? ⃗⃗⃗⃗⃗⃗ ? + ?? ?⃗ ⃗⃗⃗⃗⃗⃗⃗⃗⃗⃗⃗ (DO NOT) And ?? ⃗⃗⃗⃗⃗⃗? = −12 ? (?. ?) Find: 1. The forces acting at points B and C. 2. The corresponding values of Ry and Rz
Calculate the moment about a point C caused by the forces acting
at the points A&B respectively (engineering)?
Can somebody please help me with these 2 problems? Thanks so
much!!
Calculate the moment about a point CC – 4, 5, 7) ft caused by the forces F1 = – 4i + 4% – 8k lb and F, = – 3i – 7j + 7k lb acting at the points AC – 2, – 4, – 1) ft and B(2, 2,...
2. There are two forces acting at C. What is the resultant from the two forces? What is the moment about the point o generated from the resultant force? Find the component of the moment about point which goes in the direction of OA. (20 pts.) 1 ft 3 ft F = (-20i + 10j + 30k) lb B 2 ft F. =-101 - 30j + 50k) lb
2. There are two forces acting at C. What is the resultant from the two forces? What is the moment about the point o generated from the resultant force? Find the component of the moment about point O which goes in the direction of OA. (20 pts.) 1 ft ft 3 ft F = {-20i + 10j + 30k) lb B 2 ft F = (-10i - 30j + 50k) ID
corresponding to the two forces acting F- 1-360j+270k) N Express it as a Cartesian vector. ine the couple moment corresponding to the two forces acting e pipe system shown at right. (10 marks) 0.4 m 0.3 m FB 1360j- 270k; N
1. (4 points) Four forces are acting on a disk as shown in the Figure 1. The radius and the mass of the disk are 10 cm and 2 kg, respectively. The disk is free to rotate about a frictionless axle going through its center. (laisk = {MR2) y (a) Find the torque produced by each force. Make 10 N V2N sure to specify the directions. 15 N (b) Find the angular acceleration of the disk. (c) How many turns...
Problem 2 (10 points) Replace the forces acting on the beam cross section by an equivalent resultant force and specify where the resultant's line of action intersects the x-axis measured from O. Show your work clearly including the equation(s) that you use. Give your equivalent resultant force in terms of magnitude and direction measured counterclockwise from the +x-axis. Use 705 lb, 855 lb, 755 lb, 225 lb instead of 600 lb, 850 lb, 750 lb, 200 lb. Let a 5...
8. Plots the points on the Mohr circle of strain corresponding to the strain acting in the two perpendicular directions shown in Fig. 5 100xI56 Fig.5
B.1 Identify the forces acting on the pendulum bob: Draw a Free Body Diagram of the mass B.6 In the simulation, show the bob’s acceleration. Where is it largest and smallest? Explain why. Hint: draw a Free Body Diagram of the mass at each point.
1. Kinetics is the study of forces acting on a system.
True
False
2. Kinematics is the study of motion without regard to its
causes (forces).
True
False
3. The similarity between the Macrocycle Flowchart, the Training
Pyramid and the Goals for Performance pyramid can be best described
as an athlete should have a structured foundation and not proceed
too early.
True
False
4. When should static stretching be performed?
Minutes before event performance
Hours prior to event or the...
calculate the forces on the Wall at points A B C D
2 3-a 3
2 3-a 3