An RC circuit is used as a high-pass filter. It has a resistance of 190 ΩΩ...

Question

Question

An RC circuit is used as a high-pass filter. It has a resistance of 190 ΩΩ and capacitance of 15 pF. What is the cut-off frequency for the circuit?

science physics

Answer 1

Answer #1

Resistance, R= 190 Ohms

Capacitance, C= 15 pF

Thus, cut-off frequency,

Answer 2

Similar Homework Help Questions

2) An RC circuit is used as a high-pass lter with 200 Ω resistance and 25...

2) An RC circuit is used as a high-pass lter with 200 Ω resistance and 25 pF capacitance. There is an input signal that oscillates according to E(t) = Emax sin(ωt). (a) What is the cut-o frequency ωc of the circuit? (b) What must the input frequency ω be in order for 80% of the signal to be transmitted? if you cant answer both parts please answer b
The RC high-pass filter shown in the figure below has a resistance R = 0.500 and...

The RC high-pass filter shown in the figure below has a resistance R = 0.500 and a capacitance C - 595 pF. What is the ratio of the amplitude of the output voltage to that of the input voltage for this filter for a source frequency of 677 Hz? R Ayout Irms The voltage gain ratio is given by the following. AV R R out R z z VR² + x² Substituting 1/C for the capacitive reactance, we have the...
skipped part. Tutorial Exercise The RC high-pass filter shown in the figure below has a resistance...

skipped part. Tutorial Exercise The RC high-pass filter shown in the figure below has a resistance R -0.500 n and a capacitance C = 673 pF. What is the ratio of the amplitude of the output voltage to that of the input voltage for this filter for a source frequency of 583 Hz? R Scout Step 1 The source frequency given in this problem is not an especially high audio frequency so we might guess that the voltage transfer ratio...

Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter...

Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter with cut-off frequency of 1 kHz & gain 20dB. Design a first order active low-pass filter with cut-off frequency of 1 kHz & gain 20dB. Plot the magnitude and phase responses of the active high-pass and low-pass filters you have designed using PSpice (Use UA741 Op amp and ±12V dual supply). Connect your active low-pass and high-pass filters as shown in Fig. 1-b. Assume...
Draw a schematic for an RC Circuit that will filter out noise which exhibits a frequency...

Draw a schematic for an RC Circuit that will filter out noise which exhibits a frequency of 100 kHz. What kind of filter is this low pass or high pass? What would you change for a circuit meant to filter a frequency of 5 Hz. Would this new schematic be a high pass or low pass filter?
a high pass filter consists of a capacitor in series and a resistor in parallel to...

a high pass filter consists of a capacitor in series and a resistor in parallel to the output terminals of a circuit. It is used to "Remove low frequency signals on a circuit?", or "Remove high frequency signals on a circuit?" or "increase the inductance of a circuit?" or to "increase the resistance of the circuit?"

I want right answer Problem Design and draw a first-order op amp-RC high-pass filter with 3-dB...

I want right answer Problem Design and draw a first-order op amp-RC high-pass filter with 3-dB frequency of 10' Hz, a high-frequency input resistance of 100 k, and a high frequency-gain magnitude of 2
Problem 2: (10 points) A high pass filter with a cut-off frequency of 1200Hz is desired...

Problem 2: (10 points) A high pass filter with a cut-off frequency of 1200Hz is desired for a data acquisition system. Design the filter and specify the components for the electrical circuit that can be built into the data acquisition system.
Exercise 7: R t Envelope Detector y(0 The circuit in the figure above is a good approximation to ...

Exercise 7: R t Envelope Detector y(0 The circuit in the figure above is a good approximation to an ideal differentiator demodulator if С 0.1 h, where fe is the carrier frequency of the FM signal and fr is the cut-off frequency of the RC high-pass filter. The input FM signal is given by the following. DrM(t) 4 cos[10 nt + 10 T (5 sin(10 mt))] a) b) Specify the value of the resistance R such that fe-0.1 h, when...

Part B - Designing and analyzing a series RC high-pass filter Using the available 3.2 uF...

Part B - Designing and analyzing a series RC high-pass filter Using the available 3.2 uF capacitor, what is the value of the resistor needed to make a high-pass filter with a cutoff frequency of 2800 Hz? Express your answer to three significant figures and include appropriate units. View Available Hint(s) НА ? R = Value Units Submit Part C - Measuring the effectiveness of the series RC high-pass filter To measure the effectiveness of the design, find the magnitude...