For a circuit that contains a 50 V power supply and a 100 ohm resistor, what...

Question

Question

For a circuit that contains a 50 V power supply and a 100 ohm resistor, what power rating should be assigned to de resistor?

engineering Electrical-Engineering

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

What capacitor in series with a 100 Ohm resistor and a 20.0 mH inductor will give...

What capacitor in series with a 100 Ohm resistor and a 20.0 mH inductor will give a resonance frequency of 800 Hz? A series RLC circuit consists of a 99.0 Ohm resistor, a 0.130 H inductor, and a 20.0 muF capacitor. It is attached to a 120 V/60 Hz power line. What is the peak current I? The tuning circuit in an FM radio receiver is a series RLC circuit with a 0.2000 muH inductor. The receiver is tuned to...
Given the circuit and find the average Power absorbed by the 10 Ohm resistor. Question 4...

Given the circuit and find the average Power absorbed by the 10 Ohm resistor. Question 4 [20] Given the circuit of Fig. 3.4 find the average power absorbed by the 100 resistor -50 40 8V 220° ontv 0.1VO 81 50 Fig. 3.4 Question 5 65 lagging power factor and an efficiency
A series circuit consists of a 12 V battery, 11 Ohm resistor, 27 ohm resistor, and...

A series circuit consists of a 12 V battery, 11 Ohm resistor, 27 ohm resistor, and 36 Ohm resistor. What is the current flow through the 11 Ohm resistor?

An ac power supply produces a maximum voltage delta V_max = 100 V. This power supply...

An ac power supply produces a maximum voltage delta V_max = 100 V. This power supply is connected to a 24.0-ohm resistor, and the current and resistor voltage are measured with an ideal ac ammeter and voltmeter as shown in the sketch below: What does each meter read? An ideal ammeter has zero resistance and an ideal voltmeter has infinite resistance. (70.7 V;2.95 A)
PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and...

PI : For circuit below v-20 V and R,-8 Ohm and R2-2 Ohm. Calculate voltage and power loss in each resistor in the circuit. (Use voltage division and P = (voltage*voltage) resistance)- You cannot use KVL, KCL or Ohms law) Ri R2 P2: For circuit below i = 50 A and R1 = 15 Ohm and R2 = 10 Ohm. Calculate current and power loss in each resistor in the circuit. (Use current division and P - (current*current) resistance) You...
Two terminals a and b are attached to an unknown circuit. when a 20 ohm resistor...

Two terminals a and b are attached to an unknown circuit. when a 20 ohm resistor is connected between a and b, V=15 V across the resistor. When 20 ohm resistor is removed and a 40 ohm resistor is attached between 2 terminals, V=24 across the resistor. What is thevenin equivalent circuit at terminals a and b for unknown circuit? What is max power the circuit can deliver to a load resistor and what is the value of the load...

Design a Circuit using only 2 resistors of 15 Ohm and 1 resistor of 75 Ohm....

Design a Circuit using only 2 resistors of 15 Ohm and 1 resistor of 75 Ohm. 1. Using all three resistors, design a circuit that will draw ~320 mW from power supply when connected across 8.0 V. Determine theoretically the power consumption of each individual resistor in the circuit you have designed. 2. Annotated potential vs path graph with accompanying Kirchhoff’s Laws written as algebraic statements. 15.0Ω 7.5 Ω Current 0.40 Α) 8.0V 15.0 Ω
a 1 ohm and a 2 ohm resistor are connected in series to a 12 v...

a 1 ohm and a 2 ohm resistor are connected in series to a 12 v power supply. which resistor has greater potential difference across it?
The smallest power rating you should use for a 330 ohm (Ω) resistor with 12 volts...

The smallest power rating you should use for a 330 ohm (Ω) resistor with 12 volts (V) across it is

In the circuit, the battery voltage is 12 V, the resistor has value 100 Ohm, the...

In the circuit, the battery voltage is 12 V, the resistor has value 100 Ohm, the diode turn-on voltage is 0.6 V, and the source is a 60-Hz sine with amplitude 24 V. Determine the fraction of the time (in %) that the diode is conducting ID US(t) = G) Vs sin ar ーVB