Indicate the following concrete mechanical properties as acknowledged by the ACI 318 Code: - Minimum specified...
Indicate the following concrete mechanical properties as acknowledged by the ACI 318 Code:
-
- Minimum specified concrete strength
-
- Maximum specified concrete strength acknowledged
-
- Maximum concrete strain
-
- Minimum specified steel yield strength
-
- Maximum specified steel yield strength
-
- Maximum test yield strength for the steel
Homework Answers
According toACI 318 code-
1)Minimum specified concrete strength => 2500 psi.
2)Maximum specified concrete strength acknowledge => 7500 psi.
3)Maximum specified concrete strength acknowledge=> 0.003.
4)Minimum specified steel yield strength=> “ not be assumed
greater than the yield
point or 60,000 psi, whichever is smaller.”
5) Maximum specified steel yield strength => 75,000 psi
6)Maximum test yield strength for the steel=> 100,000 psi.
Add Answer to:
Indicate the following concrete mechanical properties as
acknowledged by the ACI 318 Code:
- Minimum specified...
of elasticity (E.) Per ACI 318-14 code, determine the modulus of rupture (f) and modulus of...
of elasticity (E.) Per ACI 318-14 code, determine the modulus of rupture (f) and modulus of elasticity (Ec) for concrete with a compressive strength of 3,500 psi. Assume the concrete is normal weight concrete. 2.
According to the ACI Building Code 318, selection of mix proportions should be based on the average strength, not the sp...
According to the ACI Building Code 318, selection of mix proportions should be based on the average strength, not the specified (design) strength. Is this justified? Given a specified strength value, what procedures are used to determine the average strength?
Following the requirements of the ACI 318-14 Standards and the information provided below determine the maximum...
Following the requirements of the ACI 318-14 Standards and the information provided below determine the maximum shear load capacity. -Rectangular reinforced concrete beam (Width = 12", Depth = 24") -Concrete Compressive Strength is 7 Ksi -Reinforcement: 3 #8 bars at 2.5" from bottom surface, #3 stirrups at 8" throughout the length of the beam -Normal weight concrete
ACI code Interaction Diagrams and Strain Compatibility for Columns The column cross-section is 300 mm x...
ACI code
Interaction Diagrams and Strain Compatibility for Columns The column cross-section is 300 mm x 500 mm and is not in contact with the ground or exposed to the weather. Ties are #10 bars and longitudinal reinforcement is # 19. Concrete compressive strength is 42 MPa and steel yield strength is 420 MPa. Calculate the axial load carrying capacity, OP and flexural capacity OM, for point in the interaction diagram with bending about the 3-3 axis where the tensile...
reinforced concrete design , ACI code Shear Strength of Flexural Members Design for shear forces The...
reinforced concrete design , ACI code
Shear Strength of Flexural Members Design for shear forces The simply supported beam shown is subjected to ultimate (factored) distributed and concentrated loads 1. Determine the shear capacity of concrete at the critical section according to ACI318-14 detailed method in Table 22.5.5.1. Design the shear reinforcement and determine the locations on the beam shear force diagram where this shear reinforcement should be placed. 2. 3. Determine the locations within the beam where minimum shear...
Problem 2 (PCC) For the corrosion protection of reinforcement in a reinforced concrete structure exposed to...
Problem 2 (PCC) For the corrosion protection of reinforcement in a reinforced concrete structure exposed to seawater, the minimum specified compressive strength (fe) is 30 MPa a) Determine the required average compressive strength (f) for the mix design if the mixing plant has a standard deviation (s) obtained from 20 test samples 3.9 MPa. b) Using the ACI code equation (Equation 7.3 pp 316), estimate the modulus of elasticity of the concrete given the required compressive strength. c) Based on...
Design a reinforced concrete beam that has a rectangular cross section with a width b =...
Design a reinforced concrete beam that has a rectangular cross section with a width b = 24 in. The depth h is limited by architectural reasons to 16 in. It has to carry a factored moment Mu = 360 kip- ft. including the self-weight. The design should satisfy ACI 318 for tension controlled members. Use Grade 60 steel and a specified concrete compressive strength = 4,000 psi. Determine the flexural reinforcement for the beam, and use compression steel if needed....
What would be the maximum aggregate size used for the given mixture properties by using ACI...
What would be the maximum aggregate size used for the given mixture properties by using ACI Method of Mix Design. 28-day specified concrete strength is 3b Mpa, standard deviation is choosen as 3.a Mpa and it is required that no more than 1 test result in 200 will fall below the specified strength. Project Title: Detoration of wood column of a commercial building Project summary: Wood deterioration at the lower level of a heavy timber column, which supports five floor...
Question 1. A concrete mix is to be designed for use in a 250 mm thick road pavement. The desired properties are pr...
Question 1. A concrete mix is to be designed for use in a 250 mm thick road pavement. The desired properties are provided below. Use the ACI method to calculate the required amounts per unit volume (/1m) of water, cement, course aggregate and fine aggregate. Slump 25 mm Average 28-day flexural strength of at least 4.5 MPa Coarse aggregate: nominal maximum size = 37.5 mm, dry-rodded weight 1600 kg/m3, specific gravity 2.68, moisture content 1.0 percent, absorption 0.5 percent Fine...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
of elasticity (E.) Per ACI 318-14 code, determine the modulus of rupture (f) and modulus of elasticity (Ec) for concrete with a compressive strength of 3,500 psi. Assume the concrete is normal weight concrete. 2.
ACI code
Interaction Diagrams and Strain Compatibility for Columns The column cross-section is 300 mm x 500 mm and is not in contact with the ground or exposed to the weather. Ties are #10 bars and longitudinal reinforcement is # 19. Concrete compressive strength is 42 MPa and steel yield strength is 420 MPa. Calculate the axial load carrying capacity, OP and flexural capacity OM, for point in the interaction diagram with bending about the 3-3 axis where the tensile...
reinforced concrete design , ACI code
Shear Strength of Flexural Members Design for shear forces The simply supported beam shown is subjected to ultimate (factored) distributed and concentrated loads 1. Determine the shear capacity of concrete at the critical section according to ACI318-14 detailed method in Table 22.5.5.1. Design the shear reinforcement and determine the locations on the beam shear force diagram where this shear reinforcement should be placed. 2. 3. Determine the locations within the beam where minimum shear...
Problem 2 (PCC) For the corrosion protection of reinforcement in a reinforced concrete structure exposed to seawater, the minimum specified compressive strength (fe) is 30 MPa a) Determine the required average compressive strength (f) for the mix design if the mixing plant has a standard deviation (s) obtained from 20 test samples 3.9 MPa. b) Using the ACI code equation (Equation 7.3 pp 316), estimate the modulus of elasticity of the concrete given the required compressive strength. c) Based on...
Question 1. A concrete mix is to be designed for use in a 250 mm thick road pavement. The desired properties are provided below. Use the ACI method to calculate the required amounts per unit volume (/1m) of water, cement, course aggregate and fine aggregate. Slump 25 mm Average 28-day flexural strength of at least 4.5 MPa Coarse aggregate: nominal maximum size = 37.5 mm, dry-rodded weight 1600 kg/m3, specific gravity 2.68, moisture content 1.0 percent, absorption 0.5 percent Fine...
Assignment 01 TOT Mechanical Properties of Materials 1. A tensile test specimen has a gage length = 50 mm and its cross-sectional area = 100 mm. The specimen yields at 48,000 N, and the corresponding gage length - 50.23 mm. This is the 0.2 ent yield point. The maximum load of 87,000 N is reached at a gage length 64.2 mm. Determine (a) yield strength, (b) modulus of elasticity, and (c) tensile strength. (d) If fracture occurs at a gage...
Most questions answered within 3 hours.
-
Where is the error in this code sequence?
String s1 = "Hello";
String s2 = "ello";...
asked 10 months ago -
Financial data for Joel de Paris, Inc., for last year
follow:
Joel de Paris, Inc.
Balance...
asked 10 months ago -
Consider this reaction:
Al2(SO4)3 (aq)+ BaCl3
(aq) Al2Cl6 (aq)- +
3BaSO4(s) . What is the...
asked 10 months ago -
Suppose that Savneet is considering increasing her
recent random sample from 20 car rentals to 40...
asked 10 months ago -
Trucks arrive at an unloading terminal at an average rate of 120
per hour.
Trucks arrive...
asked 10 months ago -
Why are methanol and ethanol completely soluble in water while
octanol is not very little soluble....
asked 10 months ago -
A facilities manager at a university reads in a research report
that the mean amount of...
asked 10 months ago -
When the CuSO4 is rehydrated by adding water to the anhydrous
compound, is this an endothermic...
asked 10 months ago -
A ray of sunlight is passing from diamond into crown glass; the
angle of incidence is...
asked 10 months ago -
A block of mass 0.249 kg is placed on top of a light, vertical
spring of...
asked 10 months ago -
how do the kidneys compensate in the presences of acidosis
a) trigger hyperventilate
b) reserve acid...
asked 10 months ago -
Question 501 pts
The rental rate of capital to the firm increases. Which of the
following...
asked 10 months ago